<6>[    0.000000@0] Booting Linux on physical CPU 0x0
<5>[    0.000000@0] Linux version 4.9.180-ga38bcc6003b4-dirty (root@BuildHost) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #44 SMP PREEMPT Mon Mar 27 19:09:17 CST 2023
<6>[    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
<6>[    0.000000@0] early_defendkey_para, base:8300000, size:100000
<6>[    0.000000@0] efi: Getting EFI parameters from FDT:
<6>[    0.000000@0] efi: UEFI not found.
<0>[    0.000000@0] 	07400000 - 07500000,     1024 KB, ramoops@0x07400000
<6>[    0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000007400000, len:36 MiB
<0>[    0.000000@0] 	05000000 - 07400000,    36864 KB, linux,secmon
<6>[    0.000000@0] __reserved_mem_alloc_size, start:0x00000000bf800000, end:0x00000000c0000000, len:8 MiB
<0>[    0.000000@0] 	bf800000 - c0000000,     8192 KB, linux,meson-fb
<6>[    0.000000@0] __reserved_mem_alloc_size, start:0x0000000078400000, end:0x0000000080400000, len:128 MiB
<0>[    0.000000@0] 	78400000 - 80400000,   131072 KB, linux,ion-dev
<6>[    0.000000@0] __reserved_mem_alloc_size, start:0x000000006c400000, end:0x0000000078400000, len:192 MiB
<0>[    0.000000@0] 	6c400000 - 78400000,   196608 KB, linux,di_cma
<6>[    0.000000@0] Reserved memory: created DMA memory pool at 0x00000000bf800000, size 0 MiB
<0>[    0.000000@0] 	bf800000 - bf800000,        0 KB, linux,ppmgr
<6>[    0.000000@0] __reserved_mem_alloc_size, start:0x0000000056000000, end:0x000000006c400000, len:356 MiB
<0>[    0.000000@0] 	56000000 - 6c400000,   364544 KB, linux,codec_mm_cma
<0>[    0.000000@0] 	bf800000 - bf800000,        0 KB, linux,codec_mm_reserved
<0>[    0.000000@0] 	bb800000 - bf800000,    65536 KB, linux,vdin0_cma
<0>[    0.000000@0] 	b7800000 - bb800000,    65536 KB, linux,vdin1_cma
<6>[    0.000000@0] cma: Reserved 8 MiB at 0x00000000b7000000
<7>[    0.000000@0] On node 0 totalpages: 786176
<7>[    0.000000@0]   DMA zone: 12284 pages used for memmap
<7>[    0.000000@0]   DMA zone: 0 pages reserved
<7>[    0.000000@0]   DMA zone: 786176 pages, LIFO batch:31
<6>[    0.000000@0] psci: probing for conduit method from DT.
<6>[    0.000000@0] psci: PSCIv1.0 detected in firmware.
<6>[    0.000000@0] psci: Using standard PSCI v0.2 function IDs
<6>[    0.000000@0] psci: Trusted OS migration not required
<6>[    0.000000@0] psci: SMC Calling Convention v1.1
<6>[    0.000000@0] percpu: Embedded 22 pages/cpu s52952 r8192 d28968 u90112
<7>[    0.000000@0] pcpu-alloc: s52952 r8192 d28968 u90112 alloc=22*4096
<7>[    0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
<6>[    0.000000@0] Detected VIPT I-cache on CPU0
<6>[    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
<6>[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 773892
<5>[    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 phy_idx= loglevel=9 hdr_priority= otg_device=1 reboot_mode_android=normal logo=osd0,loaded,0x3d800000 fb_width=1920 fb_height=1080 display_bpp=16 outputmode=1080p60hz vout=1080p60hz,enable panel_type=lcd_1 lcd_ctrl=0x00000000 hdmitx=,420,8bit hdmimode=1080p60hz hdmichecksum=0x00000000 dolby_vision_on=0 frac_rate_policy=1 hdmi_read_edid=1 cvbsmode=576cvbs osd_reverse=0 video_reverse=0 irq_check_en=0 ledsTrigger=0 androidboot.enableSystemReset=0 androidboot.enablePrivateRecovery=1 androidboot.selinux=enforcing androidboot.firstboot=0 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01-g34a1647e3e androidboot.build.expect.baseband=N/A androidboot.serialno=SKBFXYUP2CXC mac=28:CD:C4:FD:4B:62 androidboot.mac=28:CD:C4:FD:4B:62 mac_bt=A4:97:B1:40:1C:29 androidboot.mac_bt=A4:97:B1
<6>[    0.000000@0] hdmitx: hdmitx uboot phy_idx: 0
<6>[    0.000000@0] fb: osd0
<6>[    0.000000@0] fb: loaded
<6>[    0.000000@0] fb: 0x3d800000
<6>[    0.000000@0] fb: logo_info.fb_width=1920
<6>[    0.000000@0] fb: logo_info.fb_height=1080
<6>[    0.000000@0] vout: 1080p60hz
<6>[    0.000000@0] vout: enable: 1
<6>[    0.000000@0] lcd: panel_type: lcd_1
<6>[    0.000000@0] lcd: lcd_ctrl: 0x00000000
<6>[    0.000000@0] vout: get hdmimode: 1080p60hz
<6>[    0.000000@0] hdmitx: get hdmi checksum: 0x00000000
<6>[    0.000000@0] vout: get hdmi checksum: 0x00000000
<6>[    0.000000@0] get_dolby_on: 0
<6>[    0.000000@0] vout: get cvbsmode: 576cvbs
<6>[    0.000000@0] vpp_axis_reverse: bootargs is 0
<6>[    0.000000@0] DI: di_read_canvas_reverse: bootargs is 0.
<6>[    0.000000@0] vdin_get_video_reverse: bootargs is 0.
<6>[    0.000000@0] phlock_phase_config: bootargs is 0.
<6>[    0.000000@0] uboot leds trigger: 0
<6>[    0.000000@0] try to read bt mac from emmc key!
<6>[    0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
<6>[    0.000000@0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
<6>[    0.000000@0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
<6>[    0.000000@0] Memory: 2167104K/3144704K available (14844K kernel code, 2002K rwdata, 5864K rodata, 5440K init, 1513K bss, 101056K reserved, 876544K cma-reserved)
<5>[    0.000000@0] Virtual kernel memory layout:
<5>[    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
<5>[    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
<5>[    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009f00000   ( 14848 KB)
<5>[    0.000000@0]     .rodata : 0xffffff8009f00000 - 0xffffff800a4c0000   (  5888 KB)
<5>[    0.000000@0]       .init : 0xffffff800a4c0000 - 0xffffff800aa10000   (  5440 KB)
<5>[    0.000000@0]       .data : 0xffffff800aa10000 - 0xffffff800ac04a00   (  2003 KB)
<5>[    0.000000@0]        .bss : 0xffffff800ac04a00 - 0xffffff800ad7f06c   (  1514 KB)
<5>[    0.000000@0]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
<5>[    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
<5>[    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
<5>[    0.000000@0]               0xffffffbf00004000 - 0xffffffbf03000000   (    47 MB actual)
<5>[    0.000000@0]     memory  : 0xffffffc000100000 - 0xffffffc0c0000000   (  3071 MB)
<6>[    0.000000@0] can't find symbol:arm_dma_alloc
<6>[    0.000000@0] can't find symbol:__alloc_from_contiguous
<6>[    0.000000@0] can't find symbol:cma_allocator_alloc
<7>[    0.000000@0]  0, addr:ffffff8009b82ce0 +  140, aml_cma_alloc_post_hook
<7>[    0.000000@0]  1, addr:ffffff8009574190 +   78, dma_alloc_from_contiguous
<7>[    0.000000@0]  2, addr:ffffff8009231e70 +  388, cma_alloc
<7>[    0.000000@0]  3, addr:ffffff8009221818 +  310, __kmalloc_track_caller
<7>[    0.000000@0]  4, addr:ffffff800921e880 +  310, __kmalloc
<7>[    0.000000@0]  5, addr:ffffff800921e518 +  2a0, kmem_cache_alloc_trace
<7>[    0.000000@0]  6, addr:ffffff800921e280 +  298, kmem_cache_alloc
<7>[    0.000000@0]  7, addr:ffffff800921e1f8 +   88, __slab_alloc.isra.23.constprop.27
<7>[    0.000000@0]  8, addr:ffffff800921de70 +  388, ___slab_alloc.constprop.28
<7>[    0.000000@0]  9, addr:ffffff800921b958 +  5d8, new_slab
<7>[    0.000000@0] 10, addr:ffffff800920edd8 +   70, vmalloc
<7>[    0.000000@0] 11, addr:ffffff800920ecf0 +   70, vzalloc
<7>[    0.000000@0] 12, addr:ffffff800920e7a0 +  2a0, __vmalloc_node_range
<7>[    0.000000@0] 13, addr:ffffff80091f29d8 +  110, kmalloc_order_trace
<7>[    0.000000@0] 14, addr:ffffff80091f2868 +  170, kmalloc_order
<7>[    0.000000@0] 15, addr:ffffff80091d2ac8 +  170, __alloc_page_frag
<7>[    0.000000@0] 16, addr:ffffff80091d2a60 +   68, alloc_pages_exact
<7>[    0.000000@0] 17, addr:ffffff80091d2a30 +   30, get_zeroed_page
<7>[    0.000000@0] 18, addr:ffffff80091d29d8 +   58, __get_free_pages
<7>[    0.000000@0] 19, addr:ffffff80091d1bc0 +  e18, __alloc_pages_nodemask
<7>[    0.000000@0] 20, addr:ffffff80090a0648 +  250, __dma_alloc
<6>[    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
<6>[    0.000000@0] Preemptible hierarchical RCU implementation.
<6>[    0.000000@0] 	Build-time adjustment of leaf fanout to 64.
<6>[    0.000000@0] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
<6>[    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
<4>[    0.000000@0] 
<4>[    0.000000@0] **********************************************************
<4>[    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
<4>[    0.000000@0] **                                                      **
<4>[    0.000000@0] ** trace_printk() being used. Allocating extra memory.  **
<4>[    0.000000@0] **                                                      **
<4>[    0.000000@0] ** This means that this is a DEBUG kernel and it is     **
<4>[    0.000000@0] ** unsafe for production use.                           **
<4>[    0.000000@0] **                                                      **
<4>[    0.000000@0] ** If you see this message and you are not debugging    **
<4>[    0.000000@0] ** the kernel, report this immediately to your vendor!  **
<4>[    0.000000@0] **                                                      **
<4>[    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
<4>[    0.000000@0] **********************************************************
<6>[    0.000000@0] NR_IRQS:64 nr_irqs:64 0
<6>[    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
<6>[    0.000000@0] g12a_aoclkc_init: register ao clk ok!
<6>[    0.000000@0] Meson chip version = RevB (28:B - 40:0)
<6>[    0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
<6>[    0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
<6>[    0.000000@0] meson_g12a_gpu_init: register meson gpu clk
<6>[    0.000000@0] meson_g12a_media_init: register meson media clk
<6>[    0.000000@0] meson_g12a_misc_init: register amlogic g12a misc clks
<6>[    0.000000@0] meson_g12a_misc_init: done.
<6>[    0.000000@0] g12a_clkc_init initialization complete
<6>[    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
<6>[    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
<6>[    0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
<6>[    0.000034@0] meson_bc_timer: mclk->mux_reg =        (ptrval),mclk->reg =        (ptrval)
<6>[    0.000523@0] Console: colour dummy device 80x25
<6>[    0.000539@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
<6>[    0.000548@0] pid_max: default: 32768 minimum: 301
<6>[    0.000638@0] Security Framework initialized
<6>[    0.000647@0] SELinux:  Initializing.
<7>[    0.000685@0] SELinux:  Starting in permissive mode
<6>[    0.000720@0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
<6>[    0.000730@0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
<6>[    0.001374@0] ftrace: allocating 46734 entries in 183 pages
<4>[    0.092302@0] sched-energy: CPU device node has no sched-energy-costs
<6>[    0.092318@0] CPU0: update cpu_capacity 1024
<6>[    0.103948@0] ASID allocator initialised with 65536 entries
<6>[    0.144209@0] secmon: can't fine clear_range
<6>[    0.144918@0] EFI services will not be available.
<6>[    0.193055@1] Detected VIPT I-cache on CPU1
<6>[    0.193102@1] CPU1: update cpu_capacity 1024
<6>[    0.193105@1] CPU1: Booted secondary processor [410fd034]
<6>[    0.225093@2] Detected VIPT I-cache on CPU2
<6>[    0.225124@2] CPU2: update cpu_capacity 1024
<6>[    0.225126@2] CPU2: Booted secondary processor [410fd034]
<6>[    0.257198@3] Detected VIPT I-cache on CPU3
<6>[    0.257226@3] CPU3: update cpu_capacity 1024
<6>[    0.257229@3] CPU3: Booted secondary processor [410fd034]
<6>[    0.257316@0] Brought up 4 CPUs
<6>[    0.257349@0] SMP: Total of 4 processors activated.
<6>[    0.257358@0] CPU features: detected feature: 32-bit EL0 Support
<6>[    0.257454@0] CPU: All CPU(s) started at EL2
<6>[    0.257483@0] alternatives: patching kernel code
<6>[    0.259376@0] devtmpfs: initialized
<6>[    0.287339@0] DMI not present or invalid.
<6>[    0.287633@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
<6>[    0.287651@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
<6>[    0.287835@0] pinctrl core: initialized pinctrl subsystem
<6>[    0.288894@0] NET: Registered protocol family 16
<6>[    0.293301@0] schedtune: init normalization constants...
<6>[    0.293312@0] schedtune: no energy model data
<4>[    0.293319@0] schedtune: disabled!
<6>[    0.312705@0] cpuidle: using governor menu
<6>[    0.312799@0] register canvas platform driver
<6>[    0.312843@0] register rdma platform driver
<6>[    0.317298@0] vdso: 2 pages (1 code @         (ptrval), 1 data @         (ptrval))
<6>[    0.317319@0] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
<6>[    0.317748@0] DMA: preallocated 256 KiB pool for atomic allocations
<6>[    0.318079@0] clkmsr: clkmsr: driver init
<3>[    0.318088@0] codec_mm_module_init
<6>[    0.318135@0] media_configs_system_init
<6>[    0.318436@0] aml_watch_point_probe, in, wp:4
<6>[    0.318935@0] pstore: using zlib compression
<6>[    0.319685@0] console [pstore-1] enabled
<6>[    0.319727@0] pstore: Registered ramoops as persistent store backend
<6>[    0.319738@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
<6>[    0.319748@0] ramoops: ramoops_io_en:0 1 old:0x0 ftrace_size:0x40000
<6>[    0.319760@0] ramoops_io_dump=0, buffer=        (ptrval) ftrace_old_log=          (null), size=0
<6>[    0.322282@0] aml_iomap: amlogic iomap probe done
<6>[    0.322917@0] vpu: driver version: v20190329(7-g12a)
<6>[    0.322932@0] vpu: load vpu_clk: 666666667Hz(7)
<6>[    0.323149@0] vpu: clktree_init
<6>[    0.323217@0] vpu: vpu_probe OK
<6>[    0.329006@0] clkmsr: msr_clk_reg0=        (ptrval),msr_clk_reg2=        (ptrval)
<6>[    0.329029@0] clkmsr: msr_ring_reg0=        (ptrval)
<6>[    0.332020@0] audio_clocks: audio_clocks_probe done
<6>[    0.336391@0] aml_vdac_config_probe: cpu_id:4, name:meson-g12ab-vdac
<6>[    0.336595@0] aml_vdac_probe: ok
<6>[    0.336782@0] canvas_probe reg=        (ptrval),size=2000
<6>[    0.336808@0] canvas maped reg_base =        (ptrval)
<6>[    0.345416@0] rdma_probe,cpu_type:1, ver:0, len:8
<6>[    0.345625@0] rdma_register, rdma_table_addr         (ptrval) rdma_table_addr_phy b7040000 reg_buf         (ptrval)
<6>[    0.345637@0] rdma_register success, handle 1 table_size 32768
<6>[    0.345647@0] set_rdma_handle video rdma handle = 1.
<6>[    0.345692@0] classs created ok
<6>[    0.345711@0] classs file created ok
<6>[    0.346581@0] aml_snd_reg_map[0], reg:ff640000, size:2000
<6>[    0.346607@0] aml_snd_reg_map[1], reg:ff642000, size:2000
<6>[    0.346630@0] aml_snd_reg_map[2], reg:ff64a000, size:2000
<6>[    0.346653@0] aml_snd_reg_map[3], reg:ff642800, size:1800
<6>[    0.346678@0] aml_snd_reg_map[4], reg:ffd01000, size:1000
<6>[    0.346687@0] amlogic auge_snd_iomap probe done
<6>[    0.349096@0] cvbs_out: cvbsout_probe, cpu_id:3,name:meson-g12a-cvbsout
<6>[    0.349261@0] cvbs_out: clk path:0x0
<6>[    0.349276@0] cvbs_out: find performance_pal config
<6>[    0.349300@0] cvbs_out: find performance_ntsc config
<6>[    0.349323@0] cvbs_out: register cvbs module server ok
<6>[    0.349333@0] cvbs_out: register cvbs module vout2 server ok
<3>[    0.349344@0] cvbs_out: chrdev devno 264241152 for disp
<6>[    0.349563@0] cvbs_out: create cdev cvbs
<6>[    0.349574@0] cvbs_out: cvbsout_probe OK
<6>[    0.350322@0] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
<6>[    0.350421@0] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
<6>[    0.350431@0] codec_mm_probe ok
<6>[    0.630608@0] vgaarb: loaded
<5>[    0.630948@0] SCSI subsystem initialized
<6>[    0.631249@0] usbcore: registered new interface driver usbfs
<6>[    0.631320@0] usbcore: registered new interface driver hub
<6>[    0.631416@0] usbcore: registered new device driver usb
<6>[    0.631557@0] Linux video capture interface: v2.00
<6>[    0.631671@0] pps_core: LinuxPPS API ver. 1 registered
<6>[    0.631682@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
<6>[    0.631716@0] PTP clock support registered
<3>[    0.634251@0] dmi: Firmware registration failed.
<6>[    0.642203@2] secmon: reserve_mem_size:0x2300000
<6>[    0.642301@2] secmon secmon: assigned reserved memory node linux,secmon
<6>[    0.643292@2] secmon: get page:        (ptrval), 5000
<6>[    0.643313@2] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
<6>[    0.643323@2] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
<6>[    0.643714@2] fb: osd_init_module
<6>[    0.644239@2] fb: viu vsync irq: 34
<6>[    0.644263@2] fb: viu2 vsync irq: 47
<6>[    0.644388@2] 0x000000d8:Y=d8,U=0,V=0
<6>[    0.644398@2] 0x000000d9:Y=d9,U=0,V=0
<6>[    0.644408@2] 0x000000da:Y=da,U=0,V=0
<6>[    0.644417@2] 0x000000db:Y=db,U=0,V=0
<6>[    0.644426@2] 0x000000dc:Y=dc,U=0,V=0
<6>[    0.644435@2] 0x000000dd:Y=dd,U=0,V=0
<6>[    0.644655@2] fb: osd_rdma_init: rdma_table p=0xb7048000,op=0xb7048000 , v=0x        (ptrval)
<6>[    0.644689@2] rdma_register, rdma_table_addr         (ptrval) rdma_table_addr_phy b7049000 reg_buf         (ptrval)
<6>[    0.644700@2] rdma_register success, handle 2 table_size 4096
<6>[    0.644709@2] fb: osd_rdma_init:osd rdma handle = 2.
<6>[    0.644729@2] fb: mem_size: 0x800000
<6>[    0.644738@2] fb: mem_size: 0x1980000
<6>[    0.644746@2] fb: mem_size: 0x100000
<6>[    0.644755@2] fb: mem_size: 0x100000
<6>[    0.644764@2] fb: mem_size: 0x800000
<6>[    0.644823@2] meson-fb meson-fb: assigned reserved memory node linux,meson-fb
<6>[    0.644834@2] fb: reserved memory base:0x00000000bf800000, size:800000
<6>[    0.645058@2] fb: init fbdev bpp is:32
<6>[    0.646595@2] fb: set osd0 reverse as NONE
<6>[    0.658019@2] fb: osd probe OK
<6>[    0.658871@2] hdmitx: system: Ver: 20201030
<6>[    0.659018@2] hdmitx: system: hpd irq = 33, viu1_vsync = 34
<6>[    0.659776@2] hdmitx: hw: hdmitx_get_isaformat:0x0
<6>[    0.659787@2] hdmitx: hw: P_HHI_HDMI_CLK_CNTL :0x100
<6>[    0.659796@2] hdmitx: hw: P_HHI_HDMI_PLL_CNTL :0x0
<6>[    0.660031@2] hdmitx: hw: avmute set to 1
<6>[    0.790282@2] hdmitx: edid: EDID Parser:
<4>[    0.790310@2] [RX]-up_phy_addr = 2
<6>[    0.790330@2] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11
<6>[    0.790341@2] hdmitx: v1 VSVDB: len=11, sup_2160p60hz=1, low_latency=1
<6>[    0.790351@2] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11
<6>[    0.790360@2] hdmitx: v1 VSVDB: len=11, sup_2160p60hz=1, low_latency=1
<6>[    0.790375@2] hdmitx: hdmitx: get PMT vic: 97
<6>[    0.790385@2] hdmitx: edid: find IEEEOUT
<6>[    0.790403@2] hdmitx: edid: blk0 raw data
<6>[    0.790445@2] hdmitx: edid: 
<6>[    0.790445@2] 00ffffffffffff001e6d010001010101011c010380a05a780aee91a3544c9926
<6>[    0.790445@2] 0f5054a108003140454061407140818001010101010108e80030f2705a80b058
<6>[    0.790445@2] 8a0040846300001e023a801871382d40582c450040846300001e000000fd003a
<6>[    0.790445@2] 791e883c000a202020202020000000fc004c4720545620535343520a202001a7
<6>[    0.790445@2] 
<6>[    0.790445@2] 
<6>[    0.790465@2] hdmitx: edid: blk1 raw data
<6>[    0.790507@2] hdmitx: edid: 
<6>[    0.790507@2] 020360f15a6160101f66650413051403021220212215015d5e5f6263643f402f
<6>[    0.790507@2] 0957071507505507013d1ec05f7e016e030c002000b83c2000800102030467d8
<6>[    0.790507@2] 5dc401788003e200cfe305c000e3060d01e20f33eb0146d000261003257e73a4
<6>[    0.790507@2] 662150b051001b304070360040846300001e000000000000000000000000006d
<6>[    0.790507@2] 
<6>[    0.790507@2] 
<6>[    0.791215@2] hdmitx: system: fmt_attr 420,8bit
<6>[    0.791318@3] hdmitx: system: hdmi_task_handle(6260): generate hdmitx_extcon_power Uevent (1)
<6>[    0.791941@3] hdmitx: hdmitx: get vic 0 cscd 420,8bit
<6>[    0.791961@3] hdmitx: hdmitx: mode name invalid
<6>[    0.791986@3] hdmitx: hdmitx: tmds clock 0
<6>[    0.791995@3] hdmitx: hdmitx: act clock: 0
<6>[    0.792012@0] hdmitx: system: irq 2 0
<6>[    0.792225@0] hdmitx: system: plugin
<6>[    0.792308@2] vout: tvout monitor interval:500(ms), timeout cnt:20
<6>[    0.792320@2] vout: fr_policy:2
<6>[    0.792663@2] hdmitx: hdmitx_set_current_vmode[5505]
<6>[    0.792674@2] hdmitx: system: recalc before 1080p60hz 60 1, frac 0
<6>[    0.792685@2] hdmitx: system: recalc after 1080p60hz 2997 50, frac 1
<6>[    0.792694@2] hdmitx: alread display in uboot
<6>[    0.792704@2] hdmitx: system: update rx hdr info d
<6>[    0.792713@2] vout: init mode 1080p60hz set ok
<6>[    0.792723@2] vout: aml_tvout_mode_monitor
<6>[    0.926655@0] hdmitx: edid: EDID Parser:
<4>[    0.926681@0] [RX]-up_phy_addr = 2
<6>[    0.926701@0] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11
<6>[    0.926713@0] hdmitx: v1 VSVDB: len=11, sup_2160p60hz=1, low_latency=1
<6>[    0.926722@0] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11
<6>[    0.926732@0] hdmitx: v1 VSVDB: len=11, sup_2160p60hz=1, low_latency=1
<6>[    0.926747@0] hdmitx: hdmitx: get PMT vic: 97
<6>[    0.926758@0] hdmitx: edid: find IEEEOUT
<6>[    0.926775@0] hdmitx: edid: blk0 raw data
<6>[    0.926817@0] hdmitx: edid: 
<6>[    0.926817@0] 00ffffffffffff001e6d010001010101011c010380a05a780aee91a3544c9926
<6>[    0.926817@0] 0f5054a108003140454061407140818001010101010108e80030f2705a80b058
<6>[    0.926817@0] 8a0040846300001e023a801871382d40582c450040846300001e000000fd003a
<6>[    0.926817@0] 791e883c000a202020202020000000fc004c4720545620535343520a202001a7
<6>[    0.926817@0] 
<6>[    0.926817@0] 
<6>[    0.926838@0] hdmitx: edid: blk1 raw data
<6>[    0.926880@0] hdmitx: edid: 
<6>[    0.926880@0] 020360f15a6160101f66650413051403021220212215015d5e5f6263643f402f
<6>[    0.926880@0] 0957071507505507013d1ec05f7e016e030c002000b83c2000800102030467d8
<6>[    0.926880@0] 5dc401788003e200cfe305c000e3060d01e20f33eb0146d000261003257e73a4
<6>[    0.926880@0] 662150b051001b304070360040846300001e000000000000000000000000006d
<6>[    0.926880@0] 
<6>[    0.926880@0] 
<6>[    0.926900@0] hdmitx: system: update physcial size: 1600 900
<6>[    0.926912@0] hdmitx: hw: set audio
<6>[    0.926924@0] hdmitx: hw: hdmitx tx_aud_src = 0
<6>[    0.926943@0] hdmitx: fs = 0, cd = 8, tmds_clk = 0
<6>[    0.926953@0] hdmitx: hw: aud_n_para = 6144
<6>[    0.926968@0] hdmitx: hw: set channel status
<6>[    0.926989@0] hdmitx: hw: [0x10e3] = 0x1f
<6>[    0.927018@0] hdmitx: system: hdmitx_hpd_plugin_handler(6009): hdmitx_extcon_hdmi state has initialized
<6>[    0.927051@0] hdmitx: hdmitx_set_uevent[203] hdmitx_hpd=1 0
<6>[    0.970474@2] vout: try to set phy 0 to 1 
<6>[    1.010523@2] vout: try to set phy to 1 when changing hpd to 1
<6>[    1.010536@2] vout: aml_vout_probe OK
<3>[    1.011053@2] vout: error: dummy_venc_clktree_probe: get enci_top_gate error
<6>[    1.011337@2] vout: dummy_venc_probe OK
<6>[    1.012337@2] chip type:0x28
<6>[    1.012839@2] MEMORY:[100000+bff00000]
<6>[    1.012853@2] ramdump_probe, storage device:data
<6>[    1.012862@2] NO valid ramdump args:0 0
<6>[    1.012885@2] ramdump_probe, set sticky to 8c00
<6>[    1.013348@2] Advanced Linux Sound Architecture Driver Initialized.
<6>[    1.013910@2] Bluetooth: Core ver 2.22
<6>[    1.013967@2] NET: Registered protocol family 31
<6>[    1.013978@2] Bluetooth: HCI device and connection manager initialized
<6>[    1.013995@2] Bluetooth: HCI socket layer initialized
<6>[    1.014011@2] Bluetooth: L2CAP socket layer initialized
<6>[    1.014054@2] Bluetooth: SCO socket layer initialized
<6>[    1.014626@2] NetLabel: Initializing
<6>[    1.014637@2] NetLabel:  domain hash size = 128
<6>[    1.014646@2] NetLabel:  protocols = UNLABELED CIPSOv4
<6>[    1.014709@2] NetLabel:  unlabeled traffic allowed by default
<6>[    1.019387@2] clocksource: Switched to clocksource arch_sys_counter
<5>[    1.106973@3] VFS: Disk quotas dquot_6.6.0
<6>[    1.107085@3] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
<4>[    1.120408@1] dtv_dmd:[amldtvdemod..]aml_dtvdemod_init.
<6>[    1.121158@1] NET: Registered protocol family 2
<6>[    1.147721@1] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
<6>[    1.147946@1] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
<6>[    1.148401@1] TCP: Hash tables configured (established 32768 bind 32768)
<6>[    1.148517@1] UDP hash table entries: 2048 (order: 4, 65536 bytes)
<6>[    1.148603@1] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
<6>[    1.148887@1] NET: Registered protocol family 1
<7>[    1.148926@1] PCI: CLS 0 bytes, default 64
<6>[    1.150911@1] aml_wifi wifi: [wifi_dev_probe] no interrupt pin
<6>[    1.150931@1] aml_wifi wifi: [wifi_dev_probe] no power_on_pin
<6>[    1.150944@1] wifi: power_on_pin_OD = 0;
<6>[    1.150956@1] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
<6>[    1.151084@1] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
<6>[    1.151109@1] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
<6>[    1.151122@1] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup
<6>[    1.151133@1] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem(): 100.10.545.3
<6>[    1.151740@1] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem prealloc ok
<6>[    1.151756@1] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=0
<6>[    1.151767@1] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=0
<6>[    1.151778@1] aml_wifi wifi: [wifi_dev_probe] power_on_pin=0
<6>[    1.151789@1] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
<6>[    1.152086@0] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
<6>[    1.153482@0] Trying to unpack rootfs image as initramfs...
<6>[    1.500373@0] Freeing initrd memory: 13044K
<6>[    1.505062@0] hw perfevents: clusterb_enabled = 0
<6>[    1.505084@0] hw perfevents: cpumasks 0xf, 0x0
<6>[    1.505125@0] hw perfevents: cluster A irq = 10
<6>[    1.505237@0] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
<6>[    1.506977@2] clear:7fc00000, free:7fc00000, tick:459963 us
<6>[    1.508431@0] audit: initializing netlink subsys (disabled)
<5>[    1.508506@0] audit: type=2000 audit(1.440:1): initialized
<6>[    1.509562@0] workingset: timestamp_bits=45 max_order=20 bucket_order=0
<6>[    1.520984@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>[    1.521278@0] exFAT: Version 1.2.9
<6>[    1.522178@0] Registering sdcardfs 0.1
<6>[    1.522575@0] ntfs: driver 2.1.32 [Flags: R/O].
<6>[    1.522897@0] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
<6>[    1.523636@0] fuse init (API version 7.26)
<7>[    1.524472@0] SELinux:  Registering netfilter hooks
<6>[    1.528367@0] NET: Registered protocol family 38
<5>[    1.528387@0] Key type asymmetric registered
<5>[    1.528398@0] Asymmetric key parser 'x509' registered
<6>[    1.528656@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
<6>[    1.528672@0] io scheduler noop registered (default)
<6>[    1.528683@0] io scheduler deadline registered
<6>[    1.528873@0] io scheduler cfq registered
<5>[    1.539762@1] random: fast init done
<4>[    1.539798@0] Unable to detect cache hierarchy for CPU 0
<5>[    1.539813@1] random: crng init done
<6>[    1.550099@0] brd: module loaded
<6>[    1.561847@0] loop: module loaded
<6>[    1.562592@0] zram: Added device: zram0
<3>[    1.562970@0] mtdoops: mtd device (mtddev=name/number) must be supplied
<6>[    1.564078@0] libphy: Fixed MDIO Bus: probed
<6>[    1.564741@0] tun: Universal TUN/TAP device driver, 1.6
<6>[    1.564755@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[    1.565720@0]  REG0:Addr = 000000008f3dc02d
<6>[    1.565741@0]  ee eth reset:Addr = 00000000922758b8
<6>[    1.565760@0] read auto_cali_idx fail
<6>[    1.565774@0] Not set  cali_val for REG1
<6>[    1.566277@0] meson6-dwmac ff3f0000.ethernet: no reset control found
<6>[    1.566291@0] stmmac - user ID: 0x11, Synopsys ID: 0x37
<6>[    1.566299@0]  Ring mode enabled
<6>[    1.566309@0]  DMA HW capability register supported
<6>[    1.566317@0]  Normal descriptors
<6>[    1.566326@0]  RX Checksum Offload Engine supported
<6>[    1.566335@0] 	COE Type 2
<6>[    1.566343@0]  TX Checksum insertion supported
<6>[    1.566352@0]  Wake-Up On Lan supported
<6>[    1.566404@0] eth%d: device MAC address 28:cd:c4:fd:4b:62
<6>[    1.566413@0]  Enable RX Mitigation via HW Watchdog Timer
<6>[    1.569615@0] libphy: stmmac: probed
<6>[    1.569630@0] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
<6>[    1.569640@0] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01)
<6>[    1.571137@0] PPP generic driver version 2.4.2
<6>[    1.571356@0] PPP BSD Compression module registered
<6>[    1.571369@0] PPP Deflate Compression module registered
<6>[    1.571416@0] PPP MPPE Compression module registered
<6>[    1.571427@0] NET: Registered protocol family 24
<6>[    1.571457@0] PPTP driver version 0.8.5
<6>[    1.571853@0] usbcore: registered new interface driver r8152
<6>[    1.571922@0] usbcore: registered new interface driver asix
<6>[    1.572020@0] usbcore: registered new interface driver ax88179_178a
<6>[    1.572081@0] usbcore: registered new interface driver cdc_ether
<6>[    1.572138@0] usbcore: registered new interface driver net1080
<6>[    1.572201@0] usbcore: registered new interface driver cdc_subset
<6>[    1.572258@0] usbcore: registered new interface driver zaurus
<6>[    1.572332@0] usbcore: registered new interface driver cdc_ncm
<6>[    1.573075@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[    1.573087@0] ehci-pci: EHCI PCI platform driver
<6>[    1.573148@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<6>[    1.573181@0] ohci-pci: OHCI PCI platform driver
<6>[    1.573782@0] usbcore: registered new interface driver cdc_acm
<6>[    1.573792@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[    1.573866@0] usbcore: registered new interface driver usb-storage
<6>[    1.573983@0] usbcore: registered new interface driver usbserial
<6>[    1.574393@0] mousedev: PS/2 mouse device common for all mice
<6>[    1.574678@0] usbcore: registered new interface driver xpad
<6>[    1.574819@0] i2c /dev entries driver
<6>[    1.575117@0] IR NEC protocol handler initialized
<6>[    1.575128@0] IR RC5(x/sz) protocol handler initialized
<6>[    1.575137@0] IR RC6 protocol handler initialized
<6>[    1.575146@0] IR JVC protocol handler initialized
<6>[    1.575155@0] IR Sony protocol handler initialized
<6>[    1.575164@0] IR SANYO protocol handler initialized
<6>[    1.575174@0] IR Sharp protocol handler initialized
<6>[    1.575183@0] IR MCE Keyboard/mouse protocol handler initialized
<6>[    1.575192@0] IR XMP protocol handler initialized
<6>[    1.575283@0] usbcore: registered new interface driver uvcvideo
<6>[    1.575292@0] USB Video Class driver (1.1.1)
<6>[    1.575361@0] usbcore: registered new interface driver cx231xx
<6>[    1.575373@0] md: linear personality registered for level -1
<6>[    1.575875@0] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
<6>[    1.576034@0] device-mapper: verity-avb: AVB error handler initialized with vbmeta device: /dev/block/vbmeta
<6>[    1.576048@0] Bluetooth: HCI UART driver ver 2.3
<6>[    1.576060@0] Bluetooth: HCI UART protocol H4 registered
<6>[    1.578511@0] ledtrig-cpu: registered to indicate activity on CPUs
<6>[    1.579072@0] hidraw: raw HID events driver (C) Jiri Kosina
<6>[    1.579581@0] usbcore: registered new interface driver usbhid
<6>[    1.579595@0] usbhid: USB HID core driver
<6>[    1.579797@0] ashmem: initialized
<6>[    1.581018@0] meson_cpufreq_init: ignor dsu clk!
<6>[    1.581034@0] meson_cpufreq_init: ignor dsu pre parent clk!
<6>[    1.581087@0] value of voltage_tolerance 0
<3>[    1.581098@0] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
<6>[    1.581107@0] value of gp1_clk_target 0
<6>[    1.582421@0] cpu cpu0: meson_cpufreq_init: CPU 0 initialized
<3>[    1.583906@0] ff803000.serial: clock gate not found
<6>[    1.583957@0] meson_uart ff803000.serial: ==uart0 reg addr = 0000000081ea9d75
<6>[    1.584003@0] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 22, base_baud = 1500000) is a meson_uart
<6>[    1.584020@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
<6>[    4.320566@0] console [ttyS0] enabled
<6>[    4.324755@0] meson_uart ffd24000.serial: ==uart1 reg addr = 000000008493d994
<6>[    4.331343@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 32, base_baud = 1500000) is a meson_uart
<6>[    4.341863@0] amlogic-new-usb2-v2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff80086d2000
<3>[    4.351808@0] amlogic-new-usb3-v2 ffe09080.usb3phy: set of GPIOC_7(459) as OTG ID pin
<3>[    4.359327@0] amlogic-new-usb3-v2 ffe09080.usb3phy: ok to acquire gpio
<6>[    4.365845@0] amlogic-new-usb3-v2 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff80086dd080
<6>[    4.379609@0] aml_dma ff63e000.aml_dma: Aml dma
<6>[    4.382386@0] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
<6>[    4.387517@0] aml_tdes_dma ff63e000.aml_dma:aml_tdes: Aml TDES_dma
<6>[    4.393803@3] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
<6>[    4.402964@3] ion_dev soc:ion_dev: assigned reserved memory node linux,ion-dev
<6>[    4.408041@3] ge2d: ge2d_init_module
<6>[    4.411343@3] ge2d: ge2d_dev major:238
<6>[    4.415082@3] ge2d: clock source clk_ge2d_gate 00000000cbd7c226
<6>[    4.420905@3] ge2d: clock clk_ge2d source 00000000b81fcf94
<6>[    4.426217@3] ge2d: clock source clk_vapb_0 00000000b2a34b1b
<6>[    4.431840@3] ge2d: ge2d init clock is 500000000 HZ, VPU clock is 666666656 HZ
<6>[    4.439101@3] ge2d: ge2d clock is 499 MHZ
<6>[    4.443027@3] ge2d: find address resource
<6>[    4.447009@3] ge2d: map io source 0x000000001d8e8275,size=65536 to 0x0000000051b78c6a
<6>[    4.454804@3] ge2d: reserved mem init failed
<6>[    4.459046@3] ge2d: ge2d: pdev=000000007bdbd1f0, irq=39, clk=00000000cbd7c226
<6>[    4.466194@3] ge2d: ge2d start monitor
<6>[    4.469944@0] ge2d: ge2d workqueue monitor start
<6>[    4.470563@3] [tsync_pcr_init]init success.
<6>[    4.470866@3] amvideom vsync irq: 34
<6>[    4.470896@3] create_ge2d_work_queue video task ok
<6>[    4.471558@3] create_video_receiver video_render.0  00000000769ab56f, path_id:2 success
<6>[    4.471562@3] create_video_receiver video_render.1  0000000046569e38, path_id:3 success
<6>[    4.471644@3] hdmitx: hdcp: hdmitx_hdcp_init
<6>[    4.472282@3] vout: vout2: fr_policy:2
<6>[    4.472323@3] vout: vout2: create vout2 attribute OK
<6>[    4.472441@3] vout: vout2: vout2_fops_create OK
<6>[    4.472655@3] vout: vout2: clktree_init
<6>[    4.472774@3] vout: vout2: init mode null set ok
<6>[    4.472775@3] vout: vout2: aml_vout2_probe OK
<6>[    4.472925@3] DI: di_module_init ok.
<6>[    4.473179@3] dim:dim_module_init
<6>[    4.473628@3] dim:dim_probe:
<6>[    4.473952@3] dev_vframe_init finish
<6>[    4.475026@3] dim:match name: dim_g12a:id[16]
<6>[    4.475151@3] di_multi multi-di: assigned reserved memory node linux,di_cma
<3>[    4.475173@3] dim:warn:alloc_sct:not support:1->0
<3>[    4.475175@3] dim:warn:pout:from:3->0
<6>[    4.475180@3] dim:mem size from dts:0xc000000
<6>[    4.475204@3] dim:pre_irq:52
<6>[    4.475213@3] dim:post_irq:53
<6>[    4.475219@3] dim:no aisr_irq
<3>[    4.475226@3] dim:err:dim_get_vpu_clkb: get clk vpu error.
<6>[    4.475229@3] DI: vpu clkb <334000000, 667000000>
<6>[    4.475265@3] dim:vpu clkb =666666656.
<6>[    4.475493@3] dim:afbc_prob:ver[2],_g12a,mode[0]
<6>[    4.475496@3] dim:init ops:16:(null)
<6>[    4.475509@3] 0x000000e1:Y=e1,U=0,V=0
<6>[    4.475511@3] 0x000000e2:Y=e2,U=0,V=0
<6>[    4.475513@3] 0x000000e3:Y=e3,U=0,V=0
<6>[    4.475515@3] 0x000000f0:Y=f0,U=0,V=0
<6>[    4.475517@3] 0x000000f1:Y=f1,U=0,V=0
<6>[    4.475519@3] 0x000000f2:Y=f2,U=0,V=0
<6>[    4.475521@3] 0x000000f3:Y=f3,U=0,V=0
<6>[    4.475523@3] 0x000000f4:Y=f4,U=0,V=0
<6>[    4.475525@3] 0x000000f5:Y=f5,U=0,V=0
<6>[    4.475527@3] 0x000000f6:Y=f6,U=0,V=0
<6>[    4.475534@3] 0x000000f7:Y=f7,U=0,V=0
<6>[    4.475536@3] 0x000000f8:Y=f8,U=0,V=0
<6>[    4.475537@3] 0x000000f9:Y=f9,U=0,V=0
<6>[    4.475539@3] 0x000000fa:Y=fa,U=0,V=0
<6>[    4.475541@3] 0x000000fb:Y=fb,U=0,V=0
<6>[    4.475543@3] 0x000000fc:Y=fc,U=0,V=0
<6>[    4.475550@3] 0x000000fd:Y=fd,U=0,V=0
<6>[    4.475552@3] 0x000000fe:Y=fe,U=0,V=0
<6>[    4.475554@3] 0x000000ff:Y=ff,U=0,V=0
<6>[    4.475555@3] 0x0000003a:Y=3a,U=0,V=0
<6>[    4.475557@3] 0x0000003b:Y=3b,U=0,V=0
<6>[    4.475559@3] 0x0000003c:Y=3c,U=0,V=0
<6>[    4.475564@3] 0x0000003d:Y=3d,U=0,V=0
<6>[    4.475566@3] 0x0000003e:Y=3e,U=0,V=0
<6>[    4.475568@3] 0x0000003f:Y=3f,U=0,V=0
<6>[    4.475570@3] dim:cvs inp:0x3d~0x3e~0x3f.
<6>[    4.475899@3] .
<6>[    4.476001@3] .
<6>[    4.476001@3] dim:dim_probe:ok
<6>[    4.476139@3] dim:dim_module_init finish
<6>[    4.476143@3] dil:dil_init.
<6>[    4.476505@3] dil:dil_init ok.
<6>[    4.476545@3] vdin_drv_init: major 511
<6>[    4.478735@3] rdma_register, rdma_table_addr 000000000035f05e rdma_table_addr_phy b704a000 reg_buf 000000003a25d3c2
<6>[    4.478738@3] rdma_register success, handle 3 table_size 512
<6>[    4.478741@3] vdin_drv_probe:vdin.0 rdma hanld 3.
<6>[    4.479052@3] vdin vdin0: assigned reserved memory node linux,vdin0_cma
<6>[    4.479054@3] 
<6>[    4.479054@3]  vdin memory resource done.
<6>[    4.479060@3] vdin0 cma_mem_size = 64 MB
<6>[    4.479064@3] vdin0 irq: 37 rdma irq: 2
<6>[    4.479068@3] set_canvas_manual = 0
<3>[    4.479093@3] get fclk_div5 err
<3>[    4.479096@3] vdin_drv_probe: vdin cannot get msr clk !!!
<6>[    4.479135@3] vdin_drv_probe: driver initialized ok
<6>[    4.479228@3] rdma_register, rdma_table_addr 0000000012cc811f rdma_table_addr_phy b704b000 reg_buf 00000000fe63e773
<6>[    4.479230@3] rdma_register success, handle 4 table_size 512
<6>[    4.479232@3] vdin_drv_probe:vdin.1 rdma hanld 4.
<6>[    4.479478@3] vdin vdin1: assigned reserved memory node linux,vdin1_cma
<6>[    4.479480@3] 
<6>[    4.479480@3]  vdin memory resource done.
<6>[    4.479483@3] vdin1 cma_mem_size = 64 MB
<6>[    4.479487@3] vdin1 irq: 38 rdma irq: 4
<6>[    4.479490@3] set_canvas_manual = 0
<3>[    4.479508@3] get fclk_div5 err
<3>[    4.479511@3] vdin_drv_probe: vdin cannot get msr clk !!!
<6>[    4.479517@3] vdin_debugfs_init only support debug vdin0 1
<6>[    4.479519@3] vdin_drv_probe: driver initialized ok
<6>[    4.479696@3] vdin_drv_init: vdin driver init done
<6>[    4.479700@3] [viuin..]viuin_init_module viuin module init
<6>[    4.480090@3] [viuin..]viuin_probe probe ok.
<4>[    4.480635@3] [RX]-hdmirx: hdmirx_init.
<6>[    4.480637@3] ESM HLD: Initializing...
<6>[    4.481381@3] amvdec_csi module: init.
<6>[    4.481387@3] amvdec_csi_init_module:major 509
<6>[    4.481568@3] amvdec_csi module: init. ok
<6>[    4.481573@3] amlvid:info: amlvideo_init called
<6>[    4.481573@3] amlvid:info: amlvideo_create_instance called
<6>[    4.481576@3] amlvid:info: v4l2_dev.name=:amlvideo-000
<6>[    4.481739@3] amlvideo-000: V4L2 device registered as video10
<6>[    4.481741@3] amlvid:info: amlvideo_create_instance called
<6>[    4.481743@3] amlvid:info: v4l2_dev.name=:amlvideo-001
<6>[    4.481845@3] amlvideo-001: V4L2 device registered as video23
<3>[    4.482039@3] amlvideo2 probe called
<6>[    4.482197@3] amlvideo2_create_node
<6>[    4.482197@3] amlvideo2: V4L2 device registered as video11
<3>[    4.482227@3] amlvideo2 probe called
<6>[    4.482375@3] amlvideo2_create_node
<6>[    4.482375@3] amlvideo2: V4L2 device registered as video12
<4>[    4.482430@3] PPMGRDRV: warn: ppmgr module init func called
<6>[    4.482627@3] PPMGRDRV: info: ppmgr_driver_probe called
<3>[    4.482742@3] Reserved memory: failed to init DMA memory pool at 0x00000000bf800000, size 0 MiB
<6>[    4.482749@3] PPMGRDRV: info: ppmgr_dev major:508
<6>[    4.483607@3] ionvideo-000: V4L2 device registered as video13
<6>[    4.483716@3] ionvideo-001: V4L2 device registered as video14
<6>[    4.483828@3] ionvideo-002: V4L2 device registered as video15
<6>[    4.483926@3] ionvideo-003: V4L2 device registered as video16
<6>[    4.484035@3] ionvideo-004: V4L2 device registered as video17
<6>[    4.484136@3] ionvideo-005: V4L2 device registered as video18
<6>[    4.484236@3] ionvideo-006: V4L2 device registered as video19
<6>[    4.484347@3] ionvideo-007: V4L2 device registered as video20
<6>[    4.484450@3] ionvideo-008: V4L2 device registered as video21
<6>[    4.484452@3] ionvid: info: Video Technology Magazine Ion Video
<6>[    4.484454@3] ionvid: info: Capture Board ver 1.0 successfully loaded
<6>[    4.484787@3] picdec: picdec_driver_probe called.
<4>[    4.485064@3] picdec: probe of picdec failed with error -22
<6>[    4.485272@3] videosync_create_instance dev_s 00000000f61f6886,dev_s->dev 0000000034d2888b
<6>[    4.485275@3] videosync_create_instance reg videosync.0
<6>[    4.485353@1] videosync_thread started
<6>[    4.485576@3] v4lvideo-000: V4L2 device registered as video30
<6>[    4.485681@3] v4lvideo-001: V4L2 device registered as video31
<6>[    4.485779@3] v4lvideo-002: V4L2 device registered as video32
<6>[    4.485893@1] v4lvideo-003: V4L2 device registered as video33
<6>[    4.486000@1] v4lvideo-004: V4L2 device registered as video34
<6>[    4.486110@1] v4lvideo-005: V4L2 device registered as video35
<6>[    4.486211@1] v4lvideo-006: V4L2 device registered as video36
<6>[    4.486312@1] v4lvideo-007: V4L2 device registered as video37
<6>[    4.486414@1] v4lvideo-008: V4L2 device registered as video38
<3>[    4.486419@1] video_composer_module_init_1
<3>[    4.486719@1] video_composer_probe_3.1:ports[i].name=video_composer.0, i=0
<3>[    4.486816@1] video_composer_probe_3.1:ports[i].name=video_composer.1, i=1
<3>[    4.486901@1] video_composer_probe num=2
<6>[    4.487041@1] videotunnel init
<6>[    4.487633@1] aml_vecm_init:module init
<6>[    4.487905@1] 
<6>[    4.487905@1]  VECM probe start
<6>[    4.488195@1] Can't find  detect_colorbar.
<6>[    4.488197@1] Can't find  detect_face.
<6>[    4.488200@1] Can't find  detect_corn.
<6>[    4.488202@1] Can't find  wb_sel.
<6>[    4.488204@1] hdr:Can't find  cfg_en_osd_100.
<6>[    4.488211@1] amlogic, vecm
<6>[    4.488211@1] vlock dt support: 1
<6>[    4.488212@1] vlock dt new_fsm: 0
<6>[    4.488214@1] vlock dt hwver: 0
<6>[    4.488215@1] vlock dt phlock_en: 0
<6>[    4.488218@1] Can't find  vlock_en.
<6>[    4.488220@1] Can't find  vlock_mode.
<6>[    4.488222@1] Can't find  vlock_pll_m_limit.
<6>[    4.488224@1] Can't find  vlock_line_limit.
<6>[    4.488236@1] param_config vlock_en:1 md=0x4
<6>[    4.488241@1] vlock: maxLine 524,maxPixel 1715
<6>[    4.488243@1] vlock_status_init vlock_en:1
<3>[    4.488246@1] pixel_probe: vpp probe func error!
<6>[    4.488266@1] aml_vecm_probe: ok
<6>[    4.488319@1] amdolby_vision_init:module init
<6>[    4.488619@1] 
<6>[    4.488619@1]  amdolby_vision probe start & ver: 20181220
<6>[    4.488625@1] 
<6>[    4.488625@1]  cpu_id=2 tvmode=0
<6>[    4.488766@1] dolby_vision_init_receiver(dvel)
<6>[    4.488782@1] dolby_vision_init_receiver: dvel
<6>[    4.488939@1] amdolby_vision_probe: ok
<6>[    4.488941@1] g12 dovi disable in uboot
<6>[    4.488994@1] prime_sl module init
<6>[    4.489499@1] vm_init .
<6>[    4.490476@1] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
<3>[    4.491290@1] meson-mmc: >>>>>>>>hostbase 00000000211ec6d8, dmode 
<6>[    4.491646@1] meson-mmc: actual_clock :400000, HHI_nand: 0x80
<6>[    4.491649@1] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
<6>[    4.491691@1] meson-mmc: emmc: fixdiv calc done: adj = 2d2000
<6>[    4.535416@1] meson-mmc: meson_mmc_probe() : success!
<6>[    4.539602@3] amlogic mtd driver init
<6>[    4.545387@2] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
<6>[    4.545563@2] input: aml_vkeypad as /devices/platform/rtc/input/input0
<3>[    4.546805@3] cectx ff80023c.aocec: cec driver date:2020/03/16:reduece no msg in sleep time
<3>[    4.546805@3] 
<6>[    4.546893@3] cectx ff80023c.aocec: alloc chrdev 1f6
<6>[    4.546962@3] cectx ff80023c.aocec: mode is 1b6
<6>[    4.547037@2] cectx ff80023c.aocec: mode is 1b6
<3>[    4.547058@2] cectx ff80023c.aocec: compatible:amlogic, aocec-g12a
<3>[    4.547061@2] cectx ff80023c.aocec: cecb_ver:0x1
<3>[    4.547063@2] cectx ff80023c.aocec: line_reg:0x1
<3>[    4.547066@2] cectx ff80023c.aocec: line_bit:0x3
<3>[    4.547069@2] cectx ff80023c.aocec: ee_to_ao:0x1
<6>[    4.547193@2] input: cec_input as /devices/virtual/input/input1
<3>[    4.547321@3] cectx ff80023c.aocec: not find 'port_num'
<3>[    4.547325@3] cectx ff80023c.aocec: using cec:0
<3>[    4.547352@3] cectx ff80023c.aocec: no hdmirx regs
<3>[    4.547355@3] cectx ff80023c.aocec: no hhi regs
<6>[    4.547371@3] cectx ff80023c.aocec: ao enable:int mask:0x0
<6>[    4.548431@3] cectx ff80023c.aocec: clear all logical addr
<6>[    4.549894@3] cectx ff80023c.aocec: clear all logical addr
<6>[    4.550576@3] irq cnt:2, a:36, b35
<6>[    4.550844@3] cectx ff80023c.aocec: dev init wakeup
<3>[    4.557682@1] cectx ff80023c.aocec: wakeup_reason:0x0
<3>[    4.565917@1] cectx ff80023c.aocec: cev val1: 0x0;val2: 0x0
<6>[    4.565922@1] cectx ff80023c.aocec: ao enable:int mask:0x6
<3>[    4.565924@1] cectx ff80023c.aocec: aml_cec_probe success end
<6>[    4.566351@1] unifykey: storage in base: 0xffffffc005000000
<6>[    4.566352@1] unifykey: storage out base: 0xffffffc005040000
<6>[    4.566354@1] unifykey: storage block base: 0xffffffc005080000
<6>[    4.566355@1] unifykey: probe done!
<6>[    4.566851@1] unifykey: no efuse-version set, use default value: -1
<6>[    4.566853@1] unifykey: key unify config unifykey-num is 19
<6>[    4.566942@1] unifykey: key unify fact unifykey-num is 19
<6>[    4.566951@1] unifykey: unifykey_devno: 1f500000
<6>[    4.567171@2] unifykey: device unifykeys created ok
<6>[    4.567226@2] unifykey: aml_unifykeys_init done!
<6>[    4.567318@2] meson ts init
<6>[    4.567432@2] tsensor id: 0
<6>[    4.567591@2] r1p1_tsensor_read  valid cnt is 0
<6>[    4.567612@2] tsensor trim info: 0xfa0080b5!
<6>[    4.567614@2] tsensor hireboot: 0xc0ff2af0
<6>[    4.567699@2] meson ts init
<6>[    4.567713@2] tsensor id: 1
<6>[    4.567790@2] r1p1_tsensor_read  valid cnt is 0
<6>[    4.567799@2] tsensor trim info: 0xfa0080a4!
<6>[    4.567801@2] tsensor hireboot: 0xc0ff2ae0
<6>[    4.568045@2] audio_dsp: [dsp]register dsp to char divece(257)
<6>[    4.568258@3] amaudio: amaudio: driver amaudio init!
<6>[    4.568609@2] amaudio: amaudio_init - amaudio: driver amaudio succuess!
<6>[    4.569369@1] amlkaraoke init success!
<6>[    4.569569@1] sysled: module init
<6>[    4.569874@1] meson_wdt ffd0f0d0.watchdog: start watchdog
<6>[    4.569877@1] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
<6>[    4.570120@1] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
<6>[    4.570683@3] amlogic rfkill init
<6>[    4.570851@3] enter bt_probe of_node
<4>[    4.570888@3] not get gpio_en
<4>[    4.570894@3] not get gpio_btwakeup
<6>[    4.570900@3] power on valid level is high
<6>[    4.570900@3] bt: power_on_pin_OD = 0;
<6>[    4.570903@3] bt: power_off_flag = 1;
<6>[    4.570905@3] dis power down = 0;
<3>[    4.599529@3] request_irq error ret=-22
<3>[    4.599564@3] dev_pm_set_wake_irq failed: -22
<6>[    4.600359@3] dmc_monitor_probe
<3>[    4.600539@3] page_trace_module_init, create sysfs failed
<6>[    4.600700@3] cma shrinker, adj:  0, free:18432
<6>[    4.600702@3] cma shrinker, adj:100, free:23040
<6>[    4.600704@3] cma shrinker, adj:200, free:27648
<6>[    4.600706@3] cma shrinker, adj:250, free:32256
<6>[    4.600707@3] cma shrinker, adj:900, free:36864
<6>[    4.600709@3] cma shrinker, adj:950, free:46080
<4>[    4.601762@1] atv_demod: aml_atvdemod_init: OK, atv demod version: V2.15.
<6>[    4.601972@1] defendkey ff630218.defendkey: defendkey_devno:1f300000
<6>[    4.602178@2] defendkey ff630218.defendkey: defendkey: device defendkey created ok
<6>[    4.602646@3] bl40: bl40 probe
<6>[    4.603440@2] usbcore: registered new interface driver snd-usb-audio
<6>[    4.604866@2] aml_codec_T9015 ff632000.t9015: aml_T9015_audio_codec_probe
<6>[    4.604894@2] T9015 acodec used by auge, tdmout:1
<6>[    4.607694@2] asoc debug: aml_audio_controller_probe-130
<6>[    4.608493@2] aml_tdm_platform_probe, tdm ID = 0, lane_cnt = 4
<6>[    4.608532@2] snd_tdm ff642000.audiobus:tdma: lane_mask_out = 1, lane_oe_mask_out = 0
<4>[    4.608600@2] snd_tdm ff642000.audiobus:tdma: neither mclk_pad nor mclk2pad set
<6>[    4.608721@2] aml_tdm_platform_probe(), share en = 1
<6>[    4.608721@2] No channel mask node Channel_Mask
<6>[    4.608878@2] aml_tdm_platform_probe, tdm ID = 1, lane_cnt = 4
<6>[    4.608950@2] TDM id 1 samesource_sel:3
<6>[    4.608958@2] snd_tdm ff642000.audiobus:tdmb: lane_mask_out = 1, lane_oe_mask_out = 0
<6>[    4.609127@2] TDM id 1 output clk enable:1
<6>[    4.609157@2] aml_tdm_platform_probe(), share en = 1
<6>[    4.609157@2] No channel mask node Channel_Mask
<6>[    4.609165@2] TDM id 1 tuning clk enable:1
<6>[    4.609353@2] aml_tdm_platform_probe, tdm ID = 2, lane_cnt = 4
<6>[    4.609382@2] snd_tdm ff642000.audiobus:tdmc: lane_mask_out = 1, lane_oe_mask_out = 1
<6>[    4.609565@2] aml_tdm_platform_probe(), share en = 1
<6>[    4.609566@2] No channel mask node Channel_Mask
<7>[    4.610213@2] aml_spdif_platform_probe, spdif ID = 0
<6>[    4.610425@2] snd_spdif ff642000.audiobus:spdif: aml_spdif_get_pins error!
<7>[    4.610543@2] SPDIF id 0 asrc_id:0 auto_asrc:0
<6>[    4.610619@2] Spdif id 0 tuning clk enable:1
<7>[    4.610623@2] spdifout_play_with_zerodata, spdif id:0 enable:0
<7>[    4.610630@2] spdif_a fifo ctrl, frddr:0 type:3, 32 bits, chmask 0x3, swap 0x10
<7>[    4.610635@2] spdif_info: rate: 48000, channel status ch0_l:0x100, ch0_r:0x100, ch1_l:0x200, ch1_r:0x200
<6>[    4.610642@2] hdmitx: audio: aout notify format CT_PCM
<6>[    4.610643@2] hdmitx: audio: aout notify channel num: 2
<6>[    4.610647@2] hdmitx: hw: set audio
<6>[    4.610650@2] hdmitx: hw: hdmitx tx_aud_src = 0
<6>[    4.610666@2] hdmitx: fs = 3, cd = 8, tmds_clk = 0
<6>[    4.610669@2] hdmitx: hw: aud_n_para = 6144
<6>[    4.610677@2] hdmitx: hw: set channel status
<6>[    4.610692@2] hdmitx: hw: [0x10e3] = 0x1f
<6>[    4.610711@2] hdmitx: audio: Audio Type: PCM
<6>[    4.610713@2] hdmitx: audio: set audio param
<7>[    4.610717@2] spdif_a is set to enable
<6>[    4.610730@2] aml_spdif_platform_probe, register soc platform
<7>[    4.610767@2] aml_spdif_platform_probe, spdif ID = 1
<6>[    4.610838@2] aml_spdif_platform_probe, register soc platform
<4>[    4.611685@2] default set lane_mask_in as all lanes.
<6>[    4.611689@2] aml_pdm_platform_probe pdm filter mode from dts:1
<6>[    4.611702@2] aml_pdm_platform_probe, register soc platform
<6>[    4.612343@2] audio-ddr-manager ff642000.audiobus:ddr_manager: 0, irqs toddr 24, frddr 27
<6>[    4.612368@2] audio-ddr-manager ff642000.audiobus:ddr_manager: 1, irqs toddr 25, frddr 28
<6>[    4.612393@2] audio-ddr-manager ff642000.audiobus:ddr_manager: 2, irqs toddr 26, frddr 29
<4>[    4.612781@2] loopback ff642000.audiobus:loopback@0: check whether to update loopback chipinfo
<6>[    4.612836@2] 	datain_src:4, datain_chnum:4, datain_chumask:f
<6>[    4.612838@2] 	datalb_src:1, datalb_chnum:2, datalb_chmask:3
<6>[    4.612839@2] 	datain_lane_mask:0x5, datalb_lane_mask:0x1
<6>[    4.612841@2] datalb_format: 1, chmask for lanes: 0x3
<6>[    4.613102@2] loopback_platform_probe, p_loopback->id:0 register soc platform
<6>[    4.613480@2] audiolocker_platform_probe
<6>[    4.613918@2] resample_platform_probe
<6>[    4.614024@2] resample_clk_set, resample_pll:24575987, sclk:12287994, clk:12287994
<6>[    4.614028@2] audio_ddr_mngr: aml_set_resample(), toddr NULL
<6>[    4.614031@2] resample id = 0, new resample = 0, resample_module = 4
<6>[    4.615156@3] Register vad
<3>[    4.615851@3] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.615855@3] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.615858@3] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.615861@3] aml_card_probe error ret:-517
<6>[    4.616115@3] GACT probability NOT on
<6>[    4.616132@3] Mirror/redirect action on
<6>[    4.616142@3] u32 classifier
<6>[    4.616143@3]     Actions configured
<6>[    4.616149@3] Netfilter messages via NETLINK v0.30.
<6>[    4.616392@3] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
<6>[    4.616662@3] ctnetlink v0.93: registering with nfnetlink.
<6>[    4.616948@3] xt_time: kernel timezone is -0000
<6>[    4.617011@3] ipip: IPv4 and MPLS over IPv4 tunneling driver
<6>[    4.617413@3] gre: GRE over IPv4 demultiplexor driver
<6>[    4.617416@3] IPv4 over IPsec tunneling driver
<6>[    4.619572@3] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[    4.619729@3] arp_tables: arp_tables: (C) 2002 David S. Miller
<6>[    4.622906@3] Initializing XFRM netlink socket
<6>[    4.622935@3] IPsec XFRM device driver
<6>[    4.623554@3] NET: Registered protocol family 10
<6>[    4.624563@3] mip6: Mobile IPv6
<6>[    4.624588@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[    4.630755@3] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
<6>[    4.631860@3] NET: Registered protocol family 17
<6>[    4.631885@3] NET: Registered protocol family 15
<6>[    4.631923@3] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
<6>[    4.632031@3] Bluetooth: RFCOMM TTY layer initialized
<6>[    4.632041@3] Bluetooth: RFCOMM socket layer initialized
<6>[    4.632076@3] Bluetooth: RFCOMM ver 1.11
<6>[    4.632085@3] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[    4.632087@3] Bluetooth: BNEP filters: protocol multicast
<6>[    4.632095@3] Bluetooth: BNEP socket layer initialized
<6>[    4.632098@3] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[    4.632104@3] Bluetooth: HIDP socket layer initialized
<6>[    4.632127@3] l2tp_core: L2TP core driver, V2.0
<6>[    4.632138@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0
<6>[    4.632140@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
<6>[    4.632176@3] l2tp_netlink: L2TP netlink interface
<6>[    4.632219@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
<6>[    4.632237@3] l2tp_debugfs: L2TP debugfs support
<6>[    4.632239@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
<6>[    4.632419@3] NET: Registered protocol family 35
<5>[    4.632581@3] Key type dns_resolver registered
<5>[    4.635591@3] Registered swp emulation handler
<5>[    4.637398@3] Registered cp15_barrier emulation handler
<5>[    4.637417@3] Registered setend emulation handler
<6>[    4.637563@3] disable EAS feature
<6>[    4.645438@2] registered taskstats version 1
<3>[    4.656081@2] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.656086@2] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.656090@2] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.656093@2] aml_card_probe error ret:-517
<4>[    4.657094@2] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
<4>[    4.659424@1] meson-aml-mmc ffe07000.emmc: divider requested rate 200000000 != actual rate 199999997: ret=0
<6>[    4.659429@1] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
<6>[    4.659431@1] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000345
<6>[    4.659438@1] meson-mmc: Data 1 aligned delay is 0
<6>[    4.659442@1] meson-mmc: emmc: clk 199999997 tuning start
<6>[    4.659913@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
<6>[    4.659930@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
<6>[    4.660176@2] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x20010010
<6>[    4.660225@2] xhci-hcd xhci-hcd.0.auto: irq 15, io mem 0xff500000
<6>[    4.660896@3] hub 1-0:1.0: USB hub found
<6>[    4.660921@3] hub 1-0:1.0: 2 ports detected
<3>[    4.662029@3] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.662032@3] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.662036@3] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.662038@3] aml_card_probe error ret:-517
<3>[    4.662749@3] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.662753@3] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.662756@3] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.662757@3] aml_card_probe error ret:-517
<6>[    4.662841@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
<6>[    4.662852@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
<6>[    4.662924@3] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
<6>[    4.663606@1] hub 2-0:1.0: USB hub found
<6>[    4.663630@1] hub 2-0:1.0: 1 port detected
<3>[    4.664706@1] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.664710@1] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.664713@1] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.664716@1] aml_card_probe error ret:-517
<3>[    4.665404@1] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.665407@1] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.665411@1] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.665413@1] aml_card_probe error ret:-517
<6>[    4.666525@1] aml_vrtc rtc: setting system clock to 2023-06-01 04:59:12 UTC (1685595552)
<3>[    4.667305@1] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.667309@1] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.667312@1] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.667314@1] aml_card_probe error ret:-517
<7>[    4.667762@1] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(0000000008f4f48f)
<4>[    4.667800@1] dwc_otg: usb0: type: 0 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
<7>[    4.667811@1] dwc_otg ff400000.dwc2_a: base=0xffffff8008b00000
<7>[    4.667814@1] dwc_otg ff400000.dwc2_a: dwc_otg_device=0x000000005033a863
<4>[    4.774630@1] dwc_otg: Core Release: 3.30a
<4>[    4.774635@1] dwc_otg: Setting default values for core params
<4>[    4.774651@1] dwc_otg: curmode: 0, host_only: 0
<7>[    4.774671@1] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
<4>[    4.786924@1] dwc_otg: Using Buffer DMA mode
<4>[    4.786928@1] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
<4>[    4.786931@1] dwc_otg: Working on port type = SLAVE
<4>[    4.786936@1] dwc_otg: Dedicated Tx FIFOs mode
<3>[    4.789849@1] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.789853@1] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.789856@1] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.789859@1] aml_card_probe error ret:-517
<6>[    4.791520@2] meson_cdev probe
<3>[    4.791532@2] thermal: read gpupp failed
<6>[    4.791619@2] meson_cdev index: 0
<3>[    4.791789@2] thermal: read gpupp failed
<6>[    4.791834@2] meson_cdev index: 1
<6>[    4.791840@2] cpucore_cooling_register, max_cpu_core_num:4
<6>[    4.791945@2] meson_cdev index: 2
<3>[    4.791950@2] thermal: read gpupp failed
<6>[    4.791967@2] meson_cdev index: 3
<6>[    4.792005@2] find tzd id: 0
<6>[    4.792143@2] find tzd id: 0
<6>[    4.792181@2] meson_cdev probe done
<3>[    4.792995@2] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.792998@2] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.793002@2] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.793004@2] aml_card_probe error ret:-517
<6>[    4.793308@2] gxbb_pm: enter meson_pm_probe!
<6>[    4.793325@2] no vddio3v3_en pin
<3>[    4.793325@2] pm-meson aml_pm: Can't get switch_clk81
<6>[    4.793360@2] gxbb_pm: meson_pm_probe done
<3>[    4.794048@2] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    4.794051@2] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    4.794054@2] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    4.794056@2] aml_card_probe error ret:-517
<6>[    4.794685@2] ALSA device list:
<6>[    4.794687@2]   No soundcards found.
<6>[    5.416394@1] meson-mmc: emmc: adj_win: < 0 1 3 4 >
<6>[    5.416400@1] meson-mmc: step:4, delay1:0x4104104, delay2:0x4004104
<6>[    5.901918@0] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
<6>[    5.918785@1] meson-mmc: emmc: adj_win: < 0 1 3 4 >
<6>[    5.918790@1] meson-mmc: step:8, delay1:0x8208208, delay2:0x8008208
<6>[    5.921574@0] usb-storage 2-1:1.0: USB Mass Storage device detected
<6>[    5.921992@0] scsi host0: usb-storage 2-1:1.0
<6>[    5.923136@1] meson-mmc: emmc: adj_win: < 0 1 3 4 >
<6>[    5.923143@1] meson-mmc: step:12, delay1:0xc30c30c, delay2:0xc00c30c
<3>[    5.923763@0] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    5.923767@0] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    5.923770@0] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    5.923772@0] aml_card_probe error ret:-517
<6>[    5.927027@1] meson-mmc: emmc: adj_win: < 0 1 3 4 >
<6>[    5.927031@1] meson-mmc: step:16, delay1:0x10410410, delay2:0x10010410
<6>[    5.930734@1] meson-mmc: emmc: adj_win: < 0 1 3 4 >
<6>[    5.930737@1] meson-mmc: step:20, delay1:0x14514514, delay2:0x14014514
<6>[    5.935702@1] meson-mmc: emmc: adj_win: < 0 1 2 4 >
<6>[    5.935706@1] meson-mmc: left:3, right:0, mid:4, size:4
<6>[    5.935709@1] meson-mmc: step:0, delay1:0x0, delay2:0x0
<6>[    5.935713@1] meson-mmc: emmc: sd_emmc_regs->gclock=0x10000345,sd_emmc_regs->gadjust=0x2000
<6>[    5.935716@1] meson-mmc: delay1:0x0, delay2:0x0
<6>[    5.935819@1] emmc: new HS200 MMC card at address 0001
<6>[    5.940382@1] emmc: clock 199999997, 8-bit-bus-width
<6>[    5.940382@1]  
<6>[    5.940383@1] mmcblk0: emmc:0001 8GTF4R 7.28 GiB 
<6>[    5.940548@1] mmcblk0boot0: emmc:0001 8GTF4R partition 1 4.00 MiB
<6>[    5.940716@1] mmcblk0boot1: emmc:0001 8GTF4R partition 2 4.00 MiB
<6>[    5.940866@1] mmcblk0rpmb: emmc:0001 8GTF4R partition 3 512 KiB
<6>[    5.941845@1] meson-mmc: Enter aml_emmc_partition_ops
<6>[    5.942269@1] meson-mmc: [mmc_read_partition_tbl] mmc read partition OK!
<6>[    5.942271@1] meson-mmc: add_emmc_partition
<6>[    5.942426@1] meson-mmc: [mmcblk0p01]           bootloader  offset 0x000000000000, size 0x000000400000 
<6>[    5.942547@1] meson-mmc: [mmcblk0p02]             reserved  offset 0x000002400000, size 0x000004000000 
<6>[    5.942673@1] meson-mmc: [mmcblk0p03]                cache  offset 0x000006c00000, size 0x000043800000 
<6>[    5.942789@1] meson-mmc: [mmcblk0p04]                  env  offset 0x00004ac00000, size 0x000000800000 
<6>[    5.942900@1] meson-mmc: [mmcblk0p05]                 logo  offset 0x00004bc00000, size 0x000000800000 
<6>[    5.943015@1] meson-mmc: [mmcblk0p06]             recovery  offset 0x00004cc00000, size 0x000001800000 
<6>[    5.943130@1] meson-mmc: [mmcblk0p07]                 misc  offset 0x00004ec00000, size 0x000000800000 
<6>[    5.943242@1] meson-mmc: [mmcblk0p08]                 dtbo  offset 0x00004fc00000, size 0x000000800000 
<6>[    5.943358@1] meson-mmc: [mmcblk0p09]             cri_data  offset 0x000050c00000, size 0x000000800000 
<6>[    5.943523@1] meson-mmc: [mmcblk0p10]                param  offset 0x000051c00000, size 0x000001000000 
<6>[    5.943643@1] meson-mmc: [mmcblk0p11]                 boot  offset 0x000053400000, size 0x000001000000 
<6>[    5.943764@1] meson-mmc: [mmcblk0p12]                  rsv  offset 0x000054c00000, size 0x000001000000 
<6>[    5.943873@1] meson-mmc: [mmcblk0p13]             metadata  offset 0x000056400000, size 0x000001000000 
<6>[    5.943989@1] meson-mmc: [mmcblk0p14]               vbmeta  offset 0x000057c00000, size 0x000000200000 
<6>[    5.944105@1] meson-mmc: [mmcblk0p15]                  tee  offset 0x000058600000, size 0x000002000000 
<6>[    5.944215@1] meson-mmc: [mmcblk0p16]              factory  offset 0x00005ae00000, size 0x000000800000 
<6>[    5.944350@1] meson-mmc: [mmcblk0p17]                super  offset 0x00005be00000, size 0x000065200000 
<6>[    5.944465@1] meson-mmc: [mmcblk0p18]      factory_setting  offset 0x0000c1800000, size 0x000001000000 
<6>[    5.944581@1] meson-mmc: [mmcblk0p19]             btv_home  offset 0x0000c3000000, size 0x000006400000 
<6>[    5.944706@1] meson-mmc: [mmcblk0p20]                 data  offset 0x0000c9c00000, size 0x000108400000 
<6>[    5.944729@1] card key: card_blk_probe.
<6>[    5.944733@1] emmc_key_init:183 emmc key lba_start:0x12020,lba_end:0x12220
<6>[    5.944736@1] emmc key: emmc_key_init:205 ok.
<6>[    5.947104@1] meson-mmc: amlmmc_dtb_init: register dtb chardev
<6>[    5.947104@1] meson-mmc: calc f7778fe2, store f7778fe2
<6>[    5.949427@1] meson-mmc: calc f7778fe2, store f7778fe2
<6>[    5.949429@1] meson-mmc: total valid 2
<6>[    5.949691@1] meson-mmc: amlmmc_dtb_init: register dtb chardev OK
<6>[    5.949691@1] meson-mmc: Exit aml_emmc_partition_ops OK.
<3>[    5.951598@1] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    5.951602@1] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    5.951606@1] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    5.951609@1] aml_card_probe error ret:-517
<5>[    7.053536@0] scsi 0:0:0:0: Direct-Access     JetFlash Transcend 8GB    1100 PQ: 0 ANSI: 6
<3>[    7.054962@0] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[    7.054966@0] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[    7.054970@0] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[    7.054973@0] aml_card_probe error ret:-517
<5>[    7.056222@0] sd 0:0:0:0: [sda] 15083520 512-byte logical blocks: (7.72 GB/7.19 GiB)
<5>[    7.056807@0] sd 0:0:0:0: [sda] Write Protect is off
<7>[    7.056811@0] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
<5>[    7.057371@0] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>[    7.061103@0]  sda: sda1
<5>[    7.063374@0] sd 0:0:0:0: [sda] Attached SCSI removable disk
<6>[    7.240725@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
<6>[    7.245595@0] Freeing unused kernel memory: 5440K
<14>[    7.279200@0] init: init first stage started!
<14>[    7.279346@0] init: First stage mount skipped (recovery mode)
<14>[    7.286406@0] init: Using Android DT directory /proc/device-tree/firmware/android/
<6>[    7.300560@0] cectx ff80023c.aocec: mode is 1b6
<14>[    7.333482@3] init: [libfs_avb]Returning avb_handle with status: HashtreeDisabled
<14>[    7.363745@3] init: Loading SELinux policy
<7>[    7.368922@3] SELinux: 8192 avtab hash slots, 28026 rules.
<6>[    7.375419@1] lcd vlock_en=1, vlock_mode=0x4
<7>[    7.383952@3] SELinux: 8192 avtab hash slots, 28026 rules.
<7>[    7.383993@3] SELinux:  1 users, 2 roles, 1681 types, 0 bools, 1 sens, 1024 cats
<7>[    7.391160@3] SELinux:  97 classes, 28026 rules
<7>[    7.398755@3] SELinux:  Completing initialization.
<7>[    7.400475@3] SELinux:  Setting up existing superblocks.
<5>[    7.523570@3] audit: type=1403 audit(1685595555.356:2): policy loaded auid=4294967295 ses=4294967295
<14>[    7.527286@3] selinux: SELinux: Loaded policy from /sepolicy
<14>[    7.527286@3] 
<5>[    7.534887@3] audit: type=1404 audit(1685595555.368:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
<12>[    7.564213@3] selinux: SELinux:  Skipping /product_file_contexts:  empty file
<12>[    7.564213@3] 
<12>[    7.567563@3] selinux: SELinux:  Skipping /odm_file_contexts:  empty file
<12>[    7.567563@3] 
<14>[    7.575896@3] selinux: SELinux: Loaded file_contexts
<14>[    7.575896@3] 
<14>[    7.612769@3] init: init second stage started!
<14>[    7.639139@3] init: Using Android DT directory /proc/device-tree/firmware/android/
<12>[    7.647136@3] selinux: SELinux:  Skipping /product_file_contexts:  empty file
<12>[    7.647136@3] 
<12>[    7.650542@3] selinux: SELinux:  Skipping /odm_file_contexts:  empty file
<12>[    7.650542@3] 
<14>[    7.658814@3] selinux: SELinux: Loaded file_contexts
<14>[    7.658814@3] 
<14>[    7.665303@3] init: Running restorecon...
<12>[    7.679800@3] init: Couldn't load property file '/system/etc/prop.default': open() failed: No such file or directory: No such file or directory
<12>[    7.688190@3] init: Overriding previous 'ro.' property 'persist.sys.usb.config':'adb' with new value 'mtp'
<12>[    7.699947@3] init: Couldn't load property file '/system/build.prop': open() failed: No such file or directory: No such file or directory
<12>[    7.708997@3] init: Couldn't load property file '/vendor/default.prop': open() failed: No such file or directory: No such file or directory
<14>[    7.791747@2] ueventd: ueventd started!
<12>[    7.796346@2] selinux: SELinux:  Skipping /product_file_contexts:  empty file
<12>[    7.796346@2] 
<12>[    7.799693@2] selinux: SELinux:  Skipping /odm_file_contexts:  empty file
<12>[    7.799693@2] 
<14>[    7.808045@2] selinux: SELinux: Loaded file_contexts
<14>[    7.808045@2] 
<14>[    7.814575@2] ueventd: Parsing file /ueventd.rc...
<14>[    7.819687@2] ueventd: Parsing file /vendor/ueventd.rc...
<14>[    7.824670@2] ueventd: Unable to read config file '/vendor/ueventd.rc': open() failed: No such file or directory
<14>[    7.834803@2] ueventd: Parsing file /odm/ueventd.rc...
<14>[    7.839954@2] ueventd: Unable to read config file '/odm/ueventd.rc': open() failed: No such file or directory
<14>[    7.849792@2] ueventd: Parsing file /ueventd.amlogic.rc...
<6>[    7.864207@2] cectx ff80023c.aocec: mode is 1b6
<4>[   10.347841@2] remote: loading out-of-tree module taints kernel.
<6>[   10.349816@2] meson-remote: Driver init
<6>[   10.352408@2] meson-remote: remote_probe
<6>[   10.355864@2] meson-remote ff808040.rc: protocol = 0x1
<6>[   10.360968@2] meson-remote ff808040.rc: led_blink = 1
<6>[   10.365993@2] meson-remote ff808040.rc: led_blink_frq  = 100
<6>[   10.371664@2] meson-remote ff808040.rc: platform_data irq =31
<6>[   10.377379@2] meson-remote ff808040.rc: custom_number = 3
<6>[   10.382729@2] meson-remote ff808040.rc: ptable->map_size = 258
<6>[   10.388522@2] meson-remote ff808040.rc: ptable->custom_name = amlogic-remote-1
<6>[   10.395718@2] meson-remote ff808040.rc: ptable->custom_code = 0x7f80
<6>[   10.402042@2] meson-remote ff808040.rc: ptable->release_delay = 80
<6>[   10.408364@2] meson-remote ff808040.rc: ptable->map_size = 258
<6>[   10.413999@2] meson-remote ff808040.rc: ptable->custom_name = amlogic-remote-2
<6>[   10.421193@2] meson-remote ff808040.rc: ptable->custom_code = 0xa0f5
<6>[   10.427520@2] meson-remote ff808040.rc: ptable->release_delay = 80
<6>[   10.433840@2] meson-remote ff808040.rc: ptable->map_size = 17
<6>[   10.439393@2] meson-remote ff808040.rc: ptable->custom_name = amlogic-remote-3
<6>[   10.446586@2] meson-remote ff808040.rc: ptable->custom_code = 0xbd02
<6>[   10.452912@2] meson-remote ff808040.rc: ptable->release_delay = 80
<6>[   10.459070@2] meson-remote ff808040.rc: default protocol = 0x1 and id = 0
<6>[   10.465828@2] meson-remote ff808040.rc: reg=0x0, val=0x1f40190
<6>[   10.471633@2] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8
<6>[   10.477439@2] meson-remote ff808040.rc: reg=0x8, val=0x960050
<6>[   10.483159@2] meson-remote ff808040.rc: reg=0xc, val=0x480028
<6>[   10.488878@2] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013
<6>[   10.494858@2] meson-remote ff808040.rc: reg=0x18, val=0x8616800
<6>[   10.500751@2] meson-remote ff808040.rc: reg=0x1c, val=0x9f00
<6>[   10.506386@2] meson-remote ff808040.rc: reg=0x20, val=0x0
<6>[   10.511758@2] meson-remote ff808040.rc: reg=0x24, val=0x0
<6>[   10.517132@2] meson-remote ff808040.rc: reg=0x28, val=0x0
<6>[   10.523117@1] input: aml_keypad as /devices/platform/ff808040.rc/input/input2
<3>[   10.531878@1] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:1, error getting codec dai name:(null)
<3>[   10.540868@1] asoc-aml-card auge_sound: parse dai_link-1 fail
<3>[   10.545610@1] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
<3>[   10.555333@1] aml_card_probe error ret:-517
<4>[   10.619272@2] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
<6>[   10.620407@2] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
<12>[   10.648917@0] healthd: BatteryTemperaturePath not found
<12>[   10.648960@0] healthd: BatteryCycleCountPath not found
<6>[   10.653703@2] file system registered
<12>[   10.654741@0] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
<5>[   10.663363@0] audit: type=1400 audit(1685595558.488:4): avc:  denied  { getattr } for  pid=3234 comm="systemcontrol_s" path="/dev/kmsg" dev="tmpfs" ino=890 scontext=u:r:recovery:s0 tcontext=u:object_r:kmsg_device:s0 tclass=chr_file permissive=0
<14>[   10.664521@0] systemcontrol: [ubootenv] using /dev/block/env with size(65536) (65532)
<6>[   10.664522@0] meson-remote ff808040.rc: default protocol = 0x1 and id = 0
<6>[   10.664526@0] meson-remote ff808040.rc: reg=0x0, val=0x1f40190
<6>[   10.664528@0] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8
<6>[   10.664531@0] meson-remote ff808040.rc: reg=0x8, val=0x960050
<6>[   10.664533@0] meson-remote ff808040.rc: reg=0xc, val=0x480028
<6>[   10.664535@0] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013
<6>[   10.664538@0] meson-remote ff808040.rc: reg=0x18, val=0x8616800
<6>[   10.664540@0] meson-remote ff808040.rc: reg=0x1c, val=0x9f00
<6>[   10.664543@0] meson-remote ff808040.rc: reg=0x20, val=0x0
<6>[   10.664545@0] meson-remote ff808040.rc: reg=0x24, val=0x0
<6>[   10.664547@0] meson-remote ff808040.rc: reg=0x28, val=0x0
<6>[   10.664790@1] meson-remote ff808040.rc: default protocol = 0x1 and id = 0
<6>[   10.664793@1] meson-remote ff808040.rc: reg=0x0, val=0x1f40190
<6>[   10.664795@1] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8
<6>[   10.664798@1] meson-remote ff808040.rc: reg=0x8, val=0x960050
<6>[   10.664800@1] meson-remote ff808040.rc: reg=0xc, val=0x480028
<6>[   10.664802@1] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013
<6>[   10.664805@1] meson-remote ff808040.rc: reg=0x18, val=0x8616800
<6>[   10.664807@1] meson-remote ff808040.rc: reg=0x1c, val=0x9f00
<6>[   10.664810@1] meson-remote ff808040.rc: reg=0x20, val=0x0
<6>[   10.664812@1] meson-remote ff808040.rc: reg=0x24, val=0x0
<6>[   10.664814@1] meson-remote ff808040.rc: reg=0x28, val=0x0
<14>[   10.665585@1] systemcontrol: [ubootenv] set property count: 0
<14>[   10.674109@0] systemcontrol: display mode config path: /sbin/mesondisplay.cfgsystemcontrol: Error opening file '/vendor/etc/filteredid.cfg', No such file or directory.systemcontrol: Error -2 opening display config file /vendor/etc/filteredid.cfg.systemcontrol: display mode init type: 2 [0:none 1:tablet 2:mbox 3:tv], soc type:g12a, default UI:1080p
<6>[   10.674110@0] meson-remote ff808040.rc: default protocol = 0x1 and id = 0
<6>[   10.674115@0] meson-remote ff808040.rc: reg=0x0, val=0x1f40190
<6>[   10.674117@0] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8
<6>[   10.674120@0] meson-remote ff808040.rc: reg=0x8, val=0x960050
<6>[   10.674122@0] meson-remote ff808040.rc: reg=0xc, val=0x480028
<6>[   10.674125@0] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013
<6>[   10.674127@0] meson-remote ff808040.rc: reg=0x18, val=0x8616800
<6>[   10.674130@0] meson-remote ff808040.rc: reg=0x1c, val=0x9f00
<6>[   10.674132@0] meson-remote ff808040.rc: reg=0x20, val=0x0
<6>[   10.674135@0] meson-remote ff808040.rc: reg=0x24, val=0x0
<6>[   10.674137@0] meson-remote ff808040.rc: reg=0x28, val=0x0
<14>[   10.693872@1] recovery: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/cache
<6>[   10.736817@1] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: 
<14>[   10.737051@1] recovery: [libfs_mgr]__mount(source=/dev/block/cache,target=/cache,type=ext4)=0: Success
<5>[   10.826967@1] audit: type=1400 audit(1685595558.660:5): avc:  denied  { read } for  pid=3229 comm="recovery" name="u:object_r:persistent_properties_ready_prop:s0" dev="tmpfs" ino=12008 scontext=u:r:recovery:s0 tcontext=u:object_r:persistent_properties_ready_prop:s0 tclass=file permissive=0
<11>[   10.827241@1] recovery: [libfs_mgr]teardown: Device or resource busy
<12>[   10.977538@1] recovery: Failed to read max brightness: No such file or directory
<11>[   10.978652@3] systemcontrol: failed to set system property vendor.system.support.dolbyvision
<6>[   10.979282@2] hdmitx: system: hdmitx: set rxsense_policy as 1
<14>[   10.980573@0] systemcontrol: no one match the uevent : DEVPATH=/devices/virtual/amhdmitx/amhdmitx0/hdmi, add it to listsystemcontrol: no one match the uevent : DEVPATH=/devices/virtual/amhdmitx/amhdmitx0/hdmi_hdr, add it to listsystemcontrol: no one match the uevent : DEVPATH=/devices/virtual/amhdmitx/amhdmitx0/hdcp, add it to list
<6>[   10.980574@0] hdmitx: system: set hdcp_pwr 1
<6>[   10.983510@2] assign_ffs_buffer FFS_BUFFER_MAX=100!!!
<6>[   10.984834@2] assign_ffs_buffer FFS_BUFFER_MAX=100!!!
<14>[   11.043209@1] recovery: Screensaver disabled
<6>[   11.048383@2] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: 
<6>[   11.049267@0] fb: osd_open, 1507, fb_index=0,fb_rmem_size=26738688
<6>[   11.049406@0] fb: malloc_osd_memory, cma:00000000c4b86018
<6>[   11.049410@0] fb: malloc_osd_memory, 1201, base:0x00000000bf800000, size:8388608
<6>[   11.049412@0] fb: use ion buffer for fb memory, fb_index=0
<6>[   11.049415@0] fb: OSD0 as afbcd mode,afbc_type=2
<1>[   11.066350@3] meson-fb meson-fb: create ion_client 000000007723c9b8, handle=0000000084420ae1
<1>[   11.066356@3] meson-fb meson-fb: ion memory(0): created fb at 0x0000000048d97d74, size 25 MiB
<6>[   11.066360@3] fb:  0, phy: 0x0000000048d97d74, vir:0x000000001073c071, size=26112K
<6>[   11.066360@3] 
<6>[   11.066365@3] fb: Frame buffer memory assigned at
<6>[   11.066365@3] fb:  0, phy: 0x0000000048d97d74, vir:0x000000001073c071, size=26112K
<6>[   11.066365@3] 
<6>[   11.066368@3] fb:  0, phy: 0x0000000048d97d74, vir:0x000000001073c071, size=26112K
<6>[   11.066368@3] 
<6>[   11.066371@3] fb: logo_index=0,fb_index=0
<6>[   11.066374@3] fb: ---------------clear fb0 memory 000000001073c071
<6>[   11.070027@3] fb: osd[0] canvas.idx =0x40
<6>[   11.070029@3] fb: osd[0] canvas.addr=0x78400000
<6>[   11.070031@3] fb: osd[0] canvas.width=7680
<6>[   11.070033@3] fb: osd[0] canvas.height=2160
<6>[   11.070035@3] fb: osd[0] frame.width=1920
<6>[   11.070036@3] fb: osd[0] frame.height=1080
<6>[   11.070038@3] fb: osd[0] out_addr_id =0x1
<6>[   11.177467@2] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: 
<6>[   11.182943@2] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: 
<6>[   11.215099@3] EXT4-fs (mmcblk0p19): recovery complete
<6>[   11.216438@3] EXT4-fs (mmcblk0p19): mounted filesystem with ordered data mode. Opts: 
<6>[   11.226382@3] EXT4-fs (mmcblk0p20): mounted filesystem with ordered data mode. Opts: 
<6>[   11.262328@3] hdmitx: system: store_phy 0
<6>[   11.262551@3] hdmitx: store_avmute 2
<6>[   11.264349@3] hdmitx: hw: avmute set to 2
<6>[   11.277892@3] hdmitx: system: restore hdcp_pwr 0
<4>[   11.277966@3] amhdmitx amhdmitx0: hdmitx20: stop14
<4>[   11.281776@3] amhdmitx amhdmitx0: hdmitx20: stop22
<6>[   11.303409@2] vout: try to set phy 0 to 1 
<6>[   11.303445@2] vout: vmode set to 2160p60hz
<6>[   11.306028@2] fb: current vmode=2160p60hz, cmd: 0x10000
<6>[   11.311166@2] vlock: event MODE_CHANGE_PRE 0
<6>[   11.315414@2] hdmitx: hdmitx_set_current_vmode[5505]
<6>[   11.320336@2] hdmitx: system: recalc before 2160p60hz 60 1, frac 0
<6>[   11.326492@2] hdmitx: system: recalc after 2160p60hz 2997 50, frac 1
<6>[   11.332813@2] hdmitx: system: get current mode: 2160p60hz
<6>[   11.338186@2] hdmitx: system: update physcial size: 1600 900
<6>[   11.343862@2] hdmitx: video: already init VIC = 0  Now VIC = 353
<6>[   11.349806@2] hdmitx: hw: div40: 0
<6>[   11.381406@2] hdmitx: frac_rate = 1
<6>[   11.381424@2] hdmitx: config HPLL = 5940000 frac_rate = 1
<6>[   11.384686@2] hdmitx: HPLLv1: 0xdb3a04f7
<6>[   11.388532@2] hdmitx: config HPLL done
<6>[   11.392260@2] hdmitx: set_hpll_od3_clk_div[687] div = 6
<6>[   11.397461@2] hdmitx: j = 10  vid_clk_div = 1
<6>[   11.401799@2] hdmitx: set enc for VIC: 353
<6>[   11.447398@2] hdmitx: hw:  config hdmitx IP vic = 353 cd:4 cs: 3
<6>[   11.457854@2] hdmitx: video: Sink is HDMI device
<6>[   11.457902@2] hdmitx: hw: set audio
<6>[   11.458305@0] hdmitx: hdmitx_set_drm_pkt: tf=1, cf=1, colormetry=0
<6>[   11.466454@2] hdmitx: hw: hdmitx tx_aud_src = 0
<6>[   11.470974@2] hdmitx: fs = 3, cd = 4, tmds_clk = 593407
<6>[   11.470977@2] hdmitx: hw: aud_n_para = 5824
<6>[   11.470985@2] hdmitx: hw: set channel status
<6>[   11.471000@2] hdmitx: hw: [0x10e3] = 0x1f
<6>[   11.471018@2] hdmitx: audio: Audio Type: PCM
<6>[   11.471023@2] hdmitx: system: update rx hdr info d
<6>[   11.471027@2] vout: new mode 2160p60hz set ok
<6>[   11.471030@2] fb: current vmode=2160p60hz, cmd: 0x20000
<6>[   11.471038@2] fb: outputmode changed to 2160p60hz, reset osd0, (0, 0, 1919, 539) -> (0, 0, 3839, 2159)
<6>[   11.474945@0] hdmitx: hdmitx_set_drm_pkt: tf=16, cf=9, colormetry=0
<6>[   11.475461@0] hdmitx: vid mute 20 frames before play hdr/hlg video
<6>[   11.475494@0] fb: osd_update_disp_axis_hw:pan_data(0,0,1919,1079)
<6>[   11.475496@0] fb: osd_update_disp_axis_hw:dispdata(0,0,1919,1079)
<6>[   11.508336@0] fb: osd[0] enable: 1 (systemcontrol_s)
<6>[   11.545850@0] fb: osd_update_disp_axis_hw:pan_data(0,0,1919,1079)
<6>[   11.545852@0] fb: osd_update_disp_axis_hw:dispdata(0,0,1919,1079)
<6>[   11.564950@3] fb: osd[0] enable: 0 (recovery)
<6>[   11.575101@0] fb: osd[0] enable: 1 (recovery)
<6>[   11.591807@3] DOLBY: vout_notify_callback: VOUT_EVENT_MODE_CHANGE
<6>[   11.591811@3] vlock: event MODE_CHANGE
<5>[   11.592003@3] audit: type=1400 audit(1685595559.424:6): avc:  denied  { read } for  pid=3234 comm="systemcontrol_s" name="u:object_r:netflix_prop:s0" dev="tmpfs" ino=12001 scontext=u:r:recovery:s0 tcontext=u:object_r:netflix_prop:s0 tclass=file permissive=0
<5>[   11.592253@3] audit: type=1400 audit(1685595559.424:7): avc:  denied  { read } for  pid=3234 comm="systemcontrol_s" name="u:object_r:netflix_prop:s0" dev="tmpfs" ino=12001 scontext=u:r:recovery:s0 tcontext=u:object_r:netflix_prop:s0 tclass=file permissive=0
<5>[   11.593618@3] audit: type=1400 audit(1685595559.424:8): avc:  denied  { read } for  pid=3234 comm="systemcontrol_s" name="u:object_r:netflix_prop:s0" dev="tmpfs" ino=12001 scontext=u:r:recovery:s0 tcontext=u:object_r:netflix_prop:s0 tclass=file permissive=0
<6>[   11.595646@3] hdmitx: hdmitx: set cedst_policy as 0
<6>[   11.608433@0] hdmitx: hdmitx_set_drm_pkt: tf=1, cf=1, colormetry=0
<6>[   11.608439@0] hdmitx: hdmitx_set_drm_pkt: HDR->SDR, DRM_DB[0]=2
<6>[   11.807451@2] vout: aml_tvout_mode_work: monitor_timeout
<6>[   11.809254@0] hdmitx: hdr_work_func: send zero DRM
<5>[   11.809498@3] audit: type=1400 audit(1685595559.640:9): avc:  denied  { search } for  pid=3234 comm="systemcontrol_s" name="extcon" dev="sysfs" ino=9641 scontext=u:r:recovery:s0 tcontext=u:object_r:sysfs_extcon:s0 tclass=dir permissive=0
<14>[   12.378133@2] recovery: Starting recovery (pid 3229) on Thu Jun  1 04:59:18 2023
<14>[   12.379928@2] recovery: 
<14>[   12.382412@2] recovery: locale is [ko-KR]
<14>[   12.391784@2] recovery: start_recovery : should_wipe_cache=0
<5>[   12.395317@2] audit: type=1400 audit(1685595560.224:10): avc:  denied  { open } for  pid=3229 comm="recovery" path="/dev/__properties__/u:object_r:hal_vendor_skb_prop:s0" dev="tmpfs" ino=11984 scontext=u:r:recovery:s0 tcontext=u:object_r:hal_vendor_skb_prop:s0 tclass=file permissive=0
<14>[   12.418888@2] recovery: firmware ver=
<4>[   12.430019@0] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
<6>[   12.595804@0] fb: osd[0] enable: 0 (systemcontrol_s)
<6>[   12.609584@0] fb: osd[1] enable: 0 (systemcontrol_s)
<6>[   12.642858@0] fb: osd[0] enable: 1 (systemcontrol_s)
<6>[   13.343403@0] hdmitx: hdr_work_func: disable DRM
<5>[   13.344513@1] audit: type=1400 audit(1685595561.176:11): avc:  denied  { search } for  pid=3234 comm="systemcontrol_s" name="extcon" dev="sysfs" ino=9641 scontext=u:r:recovery:s0 tcontext=u:object_r:sysfs_extcon:s0 tclass=dir permissive=0
<6>[   13.695695@2] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[   13.698765@2] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
<6>[   17.212349@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   17.215166@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   17.218116@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   17.223227@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   17.379121@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   17.382861@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   17.383238@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   17.383242@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   17.550110@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   17.552812@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   17.555880@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   17.561001@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   17.720795@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   17.723498@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   17.726570@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   17.731798@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<14>[   26.773689@0] recovery: runUpgrade : USB_UPGRADE_MODE
<14>[   26.774093@0] recovery: current maximum temperature: 50000
<14>[   27.340970@0] recovery: Update location: /tmp/sideload/package.zip
<14>[   27.342468@0] recovery: 1 key(s) loaded from /system/etc/security/otacerts.zip
<14>[   27.348957@0] recovery: comment is 1503 bytes; signature is 1485 bytes from end
<14>[   29.126172@0] recovery: 3015-byte message too long for printk
<14>[   29.126582@0] recovery: whole-file signature verified against RSA key 0
<14>[   29.133234@0] recovery: Verifying package compatibility...
<14>[   29.138354@0] recovery: Package doesn't contain compatibility.zip entry
<5>[   29.185677@2] audit: type=1400 audit(1685595577.016:12): avc:  denied  { read } for  pid=3279 comm="update-binary" name="secure_check" dev="sysfs" ino=21156 scontext=u:r:recovery:s0 tcontext=u:object_r:sysfs:s0 tclass=file permissive=0
<6>[   29.212813@0] defendkey: mem_base_phy:8300000 mem_size:100000 mem_base_virt:000000004a3b643e
<6>[   29.216146@0] defendkey:246: copy_size:0x100000, option:0x5bf78fff00000001
<6>[   29.222497@0] decrypt_dtb: 0
<6>[   29.230330@0] defendkey:246: copy_size:0xaa000, option:0x5bf78fff00000004
<6>[   29.232089@0] decrypt_dtb: 0
<6>[   29.239805@0] defendkey: aml_sec_boot_check ok!
<5>[   29.240583@0] audit: type=1400 audit(1685595577.072:13): avc:  denied  { read } for  pid=3279 comm="update-binary" name="secure_check" dev="sysfs" ino=21156 scontext=u:r:recovery:s0 tcontext=u:object_r:sysfs:s0 tclass=file permissive=0
<5>[   29.269280@2] audit: type=1400 audit(1685595577.100:14): avc:  denied  { getattr } for  pid=3279 comm="update-binary" path="/dev/kmsg" dev="tmpfs" ino=890 scontext=u:r:recovery:s0 tcontext=u:object_r:kmsg_device:s0 tclass=chr_file permissive=0
<14>[   29.285241@1] systemcontrol: [ubootenv] using /dev/block/env with size(65536) (65532)systemcontrol: [ubootenv] set property count: 0
<14>[   29.298052@1] systemcontrol: [ubootenv] update value name [ubootenv.var.upgrade_step]: value [3] 
<14>[   29.308565@1] systemcontrol: [ubootenv] Save ubootenv to /dev/block/env succeed!
<5>[   29.451153@1] audit: type=1400 audit(1685595577.280:15): avc:  denied  { create } for  pid=32 comm="kdevtmpfs" name="dm-0" scontext=u:r:kernel:s0 tcontext=u:object_r:device:s0 tclass=blk_file permissive=0
<6>[   32.281565@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   32.284943@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   32.287350@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   32.292471@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   32.428142@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   32.430878@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   32.435346@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   32.440428@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   32.599100@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   32.602814@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   32.604855@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   32.610172@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   32.769694@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   32.773406@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   32.775449@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   32.780795@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   47.353326@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   47.356001@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   47.356397@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   47.356431@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   47.497188@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   47.499896@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   47.503078@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   47.508170@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   47.657681@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   47.660353@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   47.660763@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   47.660767@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   47.828554@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   47.831285@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   47.834439@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   47.839605@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<14>[   49.174746@3] recovery: current maximum temperature: 50900
<5>[   62.365781@2] audit: type=1400 audit(1685595610.196:16): avc:  denied  { create } for  pid=32 comm="kdevtmpfs" name="dm-1" scontext=u:r:kernel:s0 tcontext=u:object_r:device:s0 tclass=blk_file permissive=0
<6>[   62.422979@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   62.426694@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   62.428765@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   62.433878@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   62.495429@2] fb: mem_free_work, free memory: addr:800000
<6>[   62.584632@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   62.587337@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   62.590428@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   62.595581@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   62.756114@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   62.758816@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   62.761974@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   62.767001@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   62.926886@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   62.930599@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   62.932642@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   62.937963@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<14>[   69.175105@3] recovery: current maximum temperature: 50600
<12>[   70.654850@0] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
<14>[   70.985106@2] systemcontrol: SKB_VUL_TAG: Cannot open hdcp log file /sys/kernel/debug/amhdmitx/hdcp_log
<5>[   71.550842@1] audit: type=1400 audit(1685595619.380:17): avc:  denied  { create } for  pid=32 comm="kdevtmpfs" name="dm-2" scontext=u:r:kernel:s0 tcontext=u:object_r:device:s0 tclass=blk_file permissive=0
<6>[   77.493277@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   77.496318@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   77.499306@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   77.504155@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   77.637139@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   77.640177@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   77.642994@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   77.648046@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   77.800406@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   77.803110@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   77.806188@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   77.811501@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   77.971059@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   77.973764@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   77.976874@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   77.982149@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   87.144695@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based  firewall rule not found. Use the iptables CT target to attach helpers instead.
<14>[   89.175552@3] recovery: current maximum temperature: 50300
<6>[   92.564914@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   92.567631@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   92.570932@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   92.575819@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   92.721594@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   92.724363@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   92.727420@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   92.732465@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   92.892283@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   92.894982@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   92.898065@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   92.903176@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[   93.062749@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[   93.065454@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[   93.068791@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[   93.073682@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[  107.641895@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[  107.644599@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[  107.647754@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[  107.652781@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[  107.812978@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[  107.815681@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[  107.818775@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[  107.823922@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[  107.983676@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[  107.986400@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[  107.989612@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[  107.989616@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<6>[  108.154437@0] cectx ff80023c.aocec: ceca_tsklet 0x4
<6>[  108.158149@0] cectx ff80023c.aocec: cec a rx len 5:0f 87 00 e0 91 
<6>[  108.160225@0] cectx ff80023c.aocec: cec_rx_process op 0x87
<3>[  108.165316@0] cectx ff80023c.aocec: cec unsupported cmd:0x87, halflg:0x0
<14>[  109.175960@2] recovery: current maximum temperature: 51200
<5>[  114.749962@2] audit: type=1400 audit(1685595662.580:18): avc:  denied  { create } for  pid=32 comm="kdevtmpfs" name="dm-3" scontext=u:r:kernel:s0 tcontext=u:object_r:device:s0 tclass=blk_file permissive=0
<6>[  115.682226@1] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: discard
<6>[  116.466335@1] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: discard
<6>[  116.470616@1] meson-mmc: stamp 146, checksum 0xf7778fe3, version 1, magic A~D
<5>[  117.342610@0] audit: type=1400 audit(1685595665.172:19): avc:  denied  { ioctl } for  pid=3317 comm="mke2fs" path="/dev/block/factory" dev="tmpfs" ino=12993 ioctlcmd=0x127b scontext=u:r:recovery:s0 tcontext=u:object_r:factory_block_device:s0 tclass=blk_file permissive=0
<14>[  117.461268@0] systemcontrol: [ubootenv] using /dev/block/env with size(65536) (65532)systemcontrol: [ubootenv] set property count: 0
<14>[  117.467612@0] systemcontrol: [ubootenv] update value name [ubootenv.var.upgrade_step]: value [1] 
<14>[  117.478487@0] systemcontrol: [ubootenv] Save ubootenv to /dev/block/env succeed!
<14>[  117.483921@0] systemcontrol: [ubootenv] using /dev/block/env with size(65536) (65532)systemcontrol: [ubootenv] set property count: 0
<14>[  117.495654@0] systemcontrol: [ubootenv] update value name [ubootenv.var.force_auto_update]: value [false] 
<13>[  117.505352@0] systemcontrol: [ubootenv] ubootenv.var.force_auto_update not found, create it.
<14>[  117.514919@0] systemcontrol: [ubootenv] Save ubootenv to /dev/block/env succeed!
<12>[  117.853210@3] recovery: failed to read uncrypt status: No such file or directory
<14>[  117.855144@3] recovery: current maximum temperature: 51500
<14>[  117.860668@3] recovery: /tmp/sideload/package.zip
<14>[  117.865120@3] recovery: 1
<14>[  117.867715@3] recovery: time_total: 91
<14>[  117.871447@3] recovery: retry: 0
<14>[  117.874637@3] recovery: target_build: 15.536.26-20230327
<14>[  117.879934@3] recovery: bytes_written_dm-0: 601616384
<14>[  117.884960@3] recovery: bytes_stashed_dm-0: 0
<14>[  117.889294@3] recovery: bytes_written_dm-1: 176087040
